WinGD X62DF Скачать руководство пользователя страница 464

Страница: 464 / 902

PROCEDURE

If necessary, attach the eye bolt to the guide shoe (003,

Figure 8-59

NOTE:

Make sure that you install the guide shoes in their original positions.

Attach the spur-geared chain block (004) and the spur-geared chain block (001) to the
eye bolt on the guide shoe (00X).

Operate the chain blocks (004, 001) to move the guide shoe (003) through the column
door frame.

Attach the spur-geared chain block (002) to the eye bolt on the guide shoe (003).

Remove the chain blocks (001, 004).

Operate the chain block (002) to lift the guide shoe (00X).

Step 1

Step 6

for the other guide shoe.

Fig 8-59

Guide shoe - move

001

002

003

004

00753

Clean the (003,

Figure 8-60

) and all surfaces that touch.

Make sure that the surfaces of the crosshead pin (003) are clean and have no damage.

Apply to all surfaces that touch on the crosshead pin (003).

If necessary, attach the lifting tool (007) to the crosshead pin (003).

Attach the chain blocks (008, 001) to the eye bolt on the lifting tool (007).

Operate the chain blocks (008, 001) to lift the crosshead pin (003).

Operate the chain blocks (008, 001) to move the crosshead pin (003) through the
column door frame.

Attach the chain block (002) to the lifting tool (007).

Apply tension to the chain block (002).

Remove carefully the chain blocks (008).

X72DF

AA00-3326-00AAA-720A-A

Maintenance Manual

Crosshead - install

Winterthur Gas & Diesel Ltd.

- 464 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды