WinGD X62DF Скачать руководство пользователя страница 633

Страница: 633 / 902

PROCEDURE

Put the guide (006), distance ring (005), shaft (004), and the flap (001) in position
(

Put the flat bar (003), stop plate (009), flat bar (002) new tab washers (011), and screws
(010) in position. Do not tighten the screws at this step.

Put the screws (008) and new tab washers (007) in position. Do not tighten the screws
at this step.

Make sure that the shaft (004) and the flap (001) move freely.

Tighten the screws (008, 010).

Bend the tab washers (007, 011) to lock the screws (008, 010).

Fig 11-5

Flaps - install

00536

001

003

005

008

009

011

002

010

007

004

006

CLOSE UP

•

None

X72DF

AA00-6420-00AAA-720A-A

Maintenance Manual

Scavenge air receiver - install the flaps

Winterthur Gas & Diesel Ltd.

- 633 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды