WinGD X62DF Скачать руководство пользователя страница 435

Страница: 435 / 902

Attach the applicable chain (001 or 004) to the shackles (005).

Attach the chain block (002) to the chain (001 or 004).

Operate the chain block (002,

Figure 8-42

) to lift the connecting rod (001) to sufficient

height.

Attach the chain block (007) to the connecting rod (001).

Operate the chain blocks (002, 007) to move the connecting rod (001) into the position
shown in view C.

Attach the lever chain hoist (004) to the lug (005).

Attach the chain block (008) to the plate (006).

Operate the chain block (880) to lift the plate (006) up to the crosshead.

Attach the plate (006) to the rod with the two bolts and nuts.

Remove the chain block (008) from the plate (006).

Remove the lever chain hoist (003).

X72DF

AA00-3303-00AAA-720A-A

Maintenance Manual

Connecting rod - install

Winterthur Gas & Diesel Ltd.

- 435 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды