WinGD X62DF страница 283 Скачать руководство пользователя

Страница: 283 / 902

PROCEDURE

Clean all the parts of the starting air valve.

Apply a thin layer of oil to all the parts of the starting air valve.

NOTE:

Do not apply lubricant to the spindle thread (012,

Figure 7-52

) around the

synthetic locking ring.

Apply a thin layer of oil to the O-rings (005, 008).

Attach the O-rings (005, 008) to the housing (004).

Put the valve spindle (007) in the housing (004).

Put the compression spring (009) into the housing (004).

Put the piston (010) in position on the valve spindle (007).

Attach the hexagon nut (011) to the valve spindle (007).

Torque the hexagon nut (011) to the value given in section

16.1 Tightening instructions

Tap the top of the valve spindle (007) with a soft mallet. The valve spindle must spring
back to its initial position.

Attach the cover (013), together with the solenoid valve (002), to the housing (013) with
the Allen screws (001).

Torque the Allen screws.

Fig 7-52

Starting air valve - assemble

CLOSE UP

•

None

X72DF

AA00-2728-00AAA-710A-A

Maintenance Manual

Starting air valve - assemble

Winterthur Gas & Diesel Ltd.

- 283 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды