WinGD X62DF Скачать руководство пользователя страница 448

Страница: 448 / 902

Fig 8-49

Tools - prepare

001

002

003

004

006 007

008

009

010

011

012

013

005

002

00744

Remove the toggle lever (001,

Figure 8-50

) from the crosshead pin. Let the toggle lever

hang in the column.

Attach one of the two shackles (006) to the column.

Attach on of the two lever chain hoist (005) to the shackle (006) and to the platform
(004).

Operate the chain hoist (005) to lift the platform (004).

Operate the turning gear to move the platform and tools up to a sufficient height.

Attach four of the eye bolts (008) to the cylinder block (007).

Attach two of the spur-geared chain block (012) to the eye bolts (008) and the shackles
on the bracket (010).

Operate the chain blocks (012) to lift the bracket (010) to the bottom of the cylinder
block (007).

Attach the bracket (010) to the eye bolts (008).

Remove the chain blocks (012) from the shackles on the bracket (010).

Attach the spur-geared chain block (011) to the bracket (010).

X72DF

AA00-3326-00AAA-520A-A

Maintenance Manual

Crosshead - remove

Winterthur Gas & Diesel Ltd.

- 448 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды