WinGD X62DF Скачать руководство пользователя страница 305

Страница: 305 / 902

PROCEDURE

Attach the eye bolt (001,

Figure 7-62

) to the valve spindle (004).

Attach the rope to the eye bolt (001) and the engine room crane.

Put a thin layer of engineer’s blue paste on the sealing face of the valve spindle (004).

Put the valve spindle (004) in position in the valve guide bush.

Put the wooden block (003) on the valve spindle (004).

Tap the wooden block (003) with the hammer (002) three or four times.

NOTE:

During this step, do not turn the valve spindle (004) because this can cause
the sealing faces to catch.

Use the feeler gauge to do a check of the clearance X between the sealing faces of the
valve spindle (004) and valve seat (005), refer to

Table 7-2 - Exhaust valve, clearance X

Tab 7-2

Exhaust valve, clearance X

Engine type

Clearance X [mm]

X35, X35-B

0.005 to 0.020

X40, X40-B

X40DF

0.005 to 0.020

X52

X52DF

0.033 to 0.062

X62, X62-B

X62DF

0.054 to 0.070

X72, X72-B

X72DF

0.054 to 0.070

X82, X82-B

X82DF

0.120 to 0.150

X92, X92-B

X92DF

0.120 to 0.150

Remove the valve spindle (004) from the guide bush.

Do a check of the engineer’s blue paste. The paste must only show on the inner part of
the full circumference of the valve spindle.

X72DF

AA00-2751-01AAA-360A-A

Maintenance Manual

Exhaust valve - do a check of the seat

Winterthur Gas & Diesel Ltd.

- 305 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды