WinGD X62DF страница 641 Скачать руководство пользователя

Страница: 641 / 902

PROCEDURE

Electric motor - free end

Step 1.1

Step 1.28

to install the applicable electric motor at the free end:

1.1

Attach the two slings (003,

Figure 11-10

) to the electric motor (004) and the

shackle on the lifting tool (002).

1.2

Attach the engine room crane to the lifting tool (002).

1.3

Operate the engine room crane to lift and move the electric motor (004) into
position.

1.4

Attach the spur-geared chain block (011) to the shackle (001) and the shackle
on the lifting tool (002).

1.5

Attach the spur-geared chain block (009) to the shackle (010).

1.6

Operate the chain block (011) and the engine room crane until the electric motor
(004) is below the chain block (009).

1.7

Attach the chain block (009) to the shackle on the lifting tool (002).

1.8

Operate the chain block (009) to hold the weight of the electric motor (004)

1.9

Remove the engine room crane from the lifting tool (002).

1.10

Attach the spur-geared chain block (007) to the shackle (008).

1.11

Operate the chain blocks (009, 011) until the electric motor (004) is below the
chain block (007).

1.12

Attach the chain block (007) to the shackle on the lifting tool (002).

1.13

Operate the chain block (007) to hold the weight of the electric motor (004).

1.14

Carefully remove the chain block (011).

1.15

Attach the spur-geared chain block (005) to the shackle (006).

1.16

Operate the chain blocks (007, 009) to move the electric motor (004) into
position below the chain block (005).

1.17

Attach the chain block (005) to the shackle on the lifting tool (002).

1.18

Operate the chain block (005) to hold the weight of the electric motor (004).

1.19

Carefully remove the chain blocks (007, 009).

X72DF

AA00-6545-00AAA-720A-A

Maintenance Manual

Auxiliary blower - install

Winterthur Gas & Diesel Ltd.

- 641 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды