4. Programming
28
D-307083 PowerMaster-360R Installer's Guide
4.5.2 Configuring arming/disarming and exit/entry procedures
The following table provides you with a detailed description of each option and its configuration settings. To select an
option and change its configuration – refer to section 4.5.1.
Option
Configuration instructions
01:ENTRY DELAY1
02:ENTRY DELAY2
Two different entry delays allow the user to enter the protected site (while the system is in the
armed state) via dedicated exit/entry doors and routes without causing an alarm.
Following entry, the user must disarm the control panel before the entry delay expires. Slow-
rate warning beeps start sounding via the Configuration device (PC or mobile) once the door
is opened, until the last 10 seconds of the delay, during which the beeping rate increases. The
ENTRY DELAY 1
and
ENTRY DELAY 2
options allow you to program the time length of
these delays.
Options:
00 seconds
;
15 seconds
(default for entry delay 2);
30 seconds
(default for entry
delay 1);
45 seconds
;
60 seconds
;
3 minutes
and
4 minutes
.
Notes:
1. In some PowerMaster-360R variants, these menus are displayed in the
Operation Mode only (see section 4.14).
2. To comply with
EN
requirements, the entry delay must not exceed 45 sec.
03:EXIT DELAY
This option allows programming the time length of the exit delay. An exit delay allows the user
to arm the system and leave the protected site via specific routes and exit/entry doors without
causing an alarm. Slow-rate warning beeps start sounding via the Configuration device (PC or
mobile) once the arming command has been given, until the last 10 seconds of the delay,
during which the beeping rate increases.
Options:
30 seconds
;
60 seconds
(default);
90 seconds
;
120 seconds,
3 minutes
and
4 minutes
.
04:EXIT MODE
The
Exit Delay
time can be further adjusted according to your preferred exit route.
The control panel provides you with the following
Exit Mode
options:
A: normal
- The exit delay is exactly as defined.
B: arm home
- Exit delay restarts when the door is reopened during exit delay. If no
door was opened during exit delay AWAY, the control panel will be armed HOME.
C: restart>reentry
- The exit delay restarts when the door is reopened during exit delay. The
restart occurs once only. Restarting the exit delay is helpful if the user re-enters
immediately after going out to retrieve an item that he left behind.
D: end by exit
- The exit delay expires (ends) automatically when the exit door is closed even
if the defined exit delay time was not completed.
Options:
normal
(default);
arm home
;
restart>reentry
and
end by exit.
Note:
In some PowerMaster-360R variants, this menu is displayed in the Operation Mode
only (see section 4.14).
05:QUICK ARM
Define whether or not the user will be allowed to perform quick arming or not. Once quick
arming is permitted, the control panel does not request a user code before it arms the system.
Options:
OFF
(default) and
ON
(default in USA).
06:BYPASS ARM
Define whether or not the user will be allowed to manually
bypass
individual zones, or allow
the system to perform automatic bypassing
of open zones during the exit delay (i.e.
force arm
). If a zone is open and
forced arming
is not permitted, the system cannot be
armed and
NOT READY
is displayed. If
no bypass
is selected, neither manual bypassing nor
force arming is allowed which means that all zones must be secured before arming.
Options:
no bypass
(default);
force arm
and
manual bypass
(default in USA).
Notes
:
1. To comply with
EN
requirements
,
manual bypass
must be selected.
2. The
option force
arm is not applicable in the
UK
.
3. A zone in Soak Test mode that is configured as bypass will trigger a test fail event
if the system detects a potential alarm event.
4. There is no limit of reported events when a bypass zone is in Soak Test mode.
07:LATCHKEY ARM
When
ON
, a
latchkey
message will be reported by SMS message to users (see Note) upon
disarming by a
latchkey user
(users 5-8 or keyfob transmitters 5-8). This mode is useful when
parents at work want to be informed of a child’s return from school.
Options:
OFF
(default) and
ON
.
Note:
To enable the reporting, you must configure the system to report alrt events to Private
users (Latchkey belongs to the alerts group of events). Refer to section 4.6.4
REPORTED
EVENTS
option in both
VOICE REPORT
&
SMS REPORT
menus.
