Vigilantplant TDLS8000 Скачать руководство пользователя страница 54

Страница: 54 / 320

<3. Installation, Wiring, Optical Axis Adjustment, and Piping>

3-9

IM 11Y01D01-01EN

TDLS8000 Installation

CAUTION

The process window is where the laser beam passes through. Be careful not to damage or stain

the window during installation.

After mounting an alignment flange and the like to the process flange, install the TDLS8000

according to the following procedure.

(1) First fasten three M6 screws in the TDLS8000 mounting screw holes on the flange surface

of the alignment flange. Leave about 8 mm of gap from the flange surface. Do not fasten the

screw in the upper right hole as viewed from the front. The upper right screw is attached on

the TDLS8000 side.

(2) Insert the alignment flange screws that you fastened in (1) in the holes on the mounting

surface (quick connectors) of the laser unit (or sensor control unit), and then rotate the unit

clockwise.

(3) Temporarily fasten the upper right screw, and then tighten all screws evenly.

CAUTION

Carefully mount the laser unit (or sensor control unit) to prevent the O-ring from being damaged

or dropping out during assembly.

CAUTION

Anti-seizing grease is applied to the screw areas. Be careful to keep dust or the like from

adhering. If dust or the like adheres to the areas, remove the dust or the like, and then reapply

the anti-seizing grease.

Hole with a hexagonal hole

Quick connector

Alignment flange

Turn clockwise

Process flange

Figure 3.8

SCU or LU installation

3rd Edition: Jun. 10, 2016-00

Содержание TDLS8000

































































































































































































































































































































Результаты поиска

Содержание TDLS8000

Отзывы:

Бренды по названию

Популярные бренды

Vigilantplant TDLS8000, Руководство пользователя

Результаты поиска

Содержание TDLS8000

Отзывы:

Бренды по названию

Популярные бренды