Tritech MicronNav Скачать руководство пользователя

Страница: 31 / 144

Installing the System

MicronNav System

0656-SOM-00001-07

© Tritech International Ltd.

Check for correct configuration of the GPS interface by selecting Utilities from the top menu

bar followed by GPS Diagnostic from the sub-menu to open the GPS Diagnostic window, if

the GPS installation has been successful the GPS data will be visible in the window. If no

data is displayed re-check the Com Port baud rate settings and confirm the GPS receiver

is switched on.

3.2.7. Connecting optional third party High Accuracy Heading/Pitch/Roll

MRU Sensors

The USBL Dunking Transducer integral Magnetic Heading and Pitch/Roll sensor that enables

the MicronNav application to make corrections to world axis is particularly effective when

operating from a non-magnetic mobile platform/vessel or fixed dockside, however when

operating from a steel hull vessel the integral sensor will be affected by magnetic interference

from the vessel and it is recommended in this type of installation that an external ships

Compass & Motion Reference Unit (MRU) is used to provide the Heading and Pitch/Roll

information.

The other occasion when an external Compass & MRU might be considered is if a greater

degree of bearing accuracy is required from the system.

The external Compass & MRU can be connected to any of the free Serial interface connectors

available on the MicronNav100 Interface Hub (see Section 3.1.6, “Electrical Connection to

the Surface MicronNav100 Interface Hub” for serial port pin out details).

The Compass and Attitude data will sometimes be supplied from separate devices in which

case it will be necessary to use two serial ports.

Note

It is possible to use an External (Ship) Heading with the USBL Dunking

Transducer Pitch/Roll. Or, External (Ship) Heading/Pitch/Roll can be used

instead of USBL Heading/Pitch/Roll.

Seanet Pro will

auto detect

the incoming data string from the external

device, no data string setup is required (although the COM port will require to be

configured to accept the data connection as detailed below).

Heading/Pitch/Roll from a single external device

To configure the system to accept the heading & pitch/roll data from a single external device

switch on the power supply to the MicronNav100 Interface Hub and click the

Seanet Setup

icon on the desktop to display the device list, select Utilities from the top menu bar followed

by Com Setup from the sub-menu to open the

Channel Setup

page and disable the integral

sensor by un-checking Enabled check box for SeaHubE.

Configure the Compass entry for the correct COM port used for the external device input

and click the check box to enable, check the baud rate matches that of the external device

Содержание MicronNav

















































































































































Результаты поиска

Содержание MicronNav

Отзывы:

Похожие инструкции для MicronNav

Бренды по названию

Популярные бренды

Tritech MicronNav, Руководство по эксплуатации продукта

Результаты поиска

Содержание MicronNav

Отзывы:

Похожие инструкции для MicronNav

Бренды по названию

Популярные бренды