TRA C KIN G T U T ORIAL
E-2
Syst
e
m UTC d
a
t
e
a
nd t
i
m
e
w
ill
b
e
s
e
t to
hh:mm:ss dd Mmm yyyy
(Note: the t
i
me and date
j
ust entered w
ill
be
d
i
sp
l
ayed.)
wh
e
n
[
ENTE
R
]
i
s h
i
t.
P
r
e
ss
[
P
R
I
O
R
]
to
ca
n
ce
l
.
1 1. Press [EN TER] to enter the date and t
i
me
i
nto the system. Press [PRIOR] t w
i
ce
to return to the
M
a
i
n m
e
nu
.
The next step
i
n the procedure
i
s to ca
li
brate the
l
ook ang
l
es. Th
i
s requ
i
res
po
i
nt
i
ng the antenna at a kno w n pos
i
t
i
on so that the encoder offsets can be set
proper
l
y. Norma
ll
y th
i
s kno w n pos
i
t
i
on w
ill
be a sate
lli
te that
i
s w e
ll
-stat
i
on kept or
one for w h
i
ch a ca
l
cu
l
ate ephemer
i
s can be obta
i
ned.
1 2. Locate a stab
l
e sate
lli
te w
i
th a kno w n nom
i
na
l
l
ong
i
tude
i
n the operat
i
ona
l
reg
i
on and peak the antenna on the sate
lli
te (poss
i
b
l
y us
i
ng a spectrum
ana
l
yzer). If the ang
l
es are off, use a mechan
i
ca
l
i
nc
li
nometer to est
i
mate the
e
l
evat
i
on.
1 3. Set the e
l
evat
i
on ang
l
e and s w eep az
i
muth to f
i
nd the sate
lli
te. V er
i
fy that
proper sate
lli
te
i
dent
i
f
i
cat
i
on has been made.
1 4. The 7 2 0 0 A C U w
ill
ca
l
cu
l
ate the
l
ook ang
l
es for a g
i
ven
l
ong
i
tude
i
f the s
i
te
data has been set proper
l
y. From the
M
a
i
n m
e
nu
, se
l
ect
T
r
ack
i
ng fun
c
t
i
ons...
,
I
mm
e
d
i
a
t
e
t
r
ack
i
ng...
and
Mov
e
to
l
ong
i
tud
e
...
.
1 5. Se
l
ect
E.
L
ong
i
tud
e
of t
a
r
g
e
t
[
d
e
g
]
and enter the target’s
l
ong
i
tude. The
des
i
red
l
ook ang
l
es w
ill
be d
i
sp
l
ayed on the
(
L
oo
k
a
ng
l
e
s
[
d
e
g
]
)
li
ne of the
d
i
sp
l
ay. Record the va
l
ues to be used as the current pos
i
t
i
on. Press [PRIOR]
three t
i
mes to return to the
M
a
i
n m
e
nu
.
1 6. Se
l
ect
Ed
i
t syst
e
m
c
onf
i
gu
r
a
t
i
on...
and
P
os
i
t
i
on
e
n
c
od
e
r
c
onf
i
gu
r
a
t
i
on...
. Se
l
ect
En
c
od
e
r
d
ir
ec
t
i
on
and us
i
ng the up and do w n arro w keys, set the encoder
d
i
rect
i
on for each ax
i
s.
1 7. Se
l
ect
Cu
rr
e
nt pos
i
t
i
on
[
d
e
g
]
and enter va
l
ues obta
i
ned
i
n step 1 5. Press
[PRIOR] and ans w er yes to save changes. Press [PRIOR] to return to the
M
a
i
n
m
e
nu.
The steptrack defau
l
ts shou
l
d no w be set. It
i
s best to conf
i
gure the steptrack
defau
l
ts pr
i
or to bu
il
d
i
ng any OPT targets. For most systems, no target-spec
i
f
i
c
parameter ad
j
ustments w
ill
be necessary.
Содержание VertexRSI 7200
