7 2 0 0 OPERA TIO N
5 - 6 6
The parameters under th
i
s menu may be changed by se
l
ect
i
ng the des
i
red
parameter, and us
i
ng the up and do w n arro w keys, togg
li
ng through the
preprogrammed cho
i
ces. W hen the des
i
red sett
i
ng
i
s h
i
gh
li
ghted, press the
[EN TER] key.
To save the changes, press [PRIOR] and ans w er yes w hen prompted to save the
changes.
5.8.6.13 F
ac
to
r
y T
e
sts
The
F
ac
to
r
y t
e
sts...
menu conta
i
ns tests that are used at the factory dur
i
ng system
test
i
ng. These tests are ava
il
ab
l
e to the user because some of these tests may be
usefu
l
i
n the f
i
e
l
d dur
i
ng troub
l
eshoot
i
ng.
5.8.6.13.1 V
i
d
e
o T
e
sts
These tests are used to exam
i
ne the d
i
sp
l
ay for ma
l
funct
i
on
i
ng p
i
xe
l
s, data
li
nes,
etc.
The A C U must be
i
n Standby, and the port perform
i
ng the test must be at Operator
or Superv
i
sor
l
eve
l
. Dur
i
ng the test, the [ST OP]/[RESU ME] keys are st
ill
operat
i
ona
l
.
To execute the
V
i
d
e
o t
e
st
, use the fo
ll
o w
i
ng procedures.
1. From the
M
a
i
n m
e
nu...
, se
l
ect
Ed
i
t syst
e
m
c
onf
i
gu
r
a
t
i
on...
,
F
ac
to
r
y t
e
sts...
, and
V
i
d
e
o t
e
st
.
2. If the A C U
i
s not
i
n Standby mode, a message w
ill
appear a
l
ert
i
ng the operator
to th
i
s fact and w hen the [EN TER] key
i
s pressed, the A C U w
ill
return to the
menu.
If the A C U
i
s
i
n Standby mode, a w arn
i
ng message w
ill
appear to a
l
ert the user that
the d
i
sp
l
ay w
ill
be b
l
anked for the test.
3. To beg
i
n the test, ans w er yes to the prompt and press [EN TER]. Note that the
[PRIOR] key may be pressed at any t
i
me to term
i
nate the test.
4. Press
i
ng the [EN TER] key w
ill
step through the test, w
i
th the fo
ll
o w
i
ng
cond
i
t
i
ons occurr
i
ng
i
n the order
li
sted:
A
ll
p
i
xe
l
s on
A
ll
p
i
xe
l
s off (d
i
sp
l
ay b
l
ank)
Odd-numbered hor
i
zonta
l
li
nes
ill
um
i
nated
Even-numbered hor
i
zonta
l
li
nes
ill
um
i
nated
Odd-numbered vert
i
ca
l
li
nes
ill
um
i
nated
Even-numbered vert
i
ca
l
li
nes
ill
um
i
nated
Содержание VertexRSI 7200
