manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 82 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 82

PK-232 MBX – OPERATING MANUAL

BAUDOT AND ASCII OPERATION

8/91

6-5

82

Immediate Commands from the Command Mode:

"L"

Forces LETTERS case.

"N"

Forces FIGURES case.

"R"

Switches system to receive mode, forces LETTERS case.

"X"

Switches system to transmit mode and forces immediate entry into Converse
mode.

"K"

Load Transmit type ahead buffer.

"Function Key" characters embedded in transmitted text:

<CTRL-B>

Sends AAB string as a HEREIS message.

<CTRL-E>

Sends "Who Are You" request to distant station.

<CTRL-O>

Sends LETTERS shift character.

<CTRL-N>

Sends FIGURES shift character.

<CTRL-D>

Shuts off transmitter after sending character buffer.

<CTRL-F>

Sends call sign in Morse and shuts off transmitter.

<CTRL-T>

Sends the Time if the DAYTIME clock has been set.

6.5.1

Changing Speed

Assume  you've  been  receiving  at  45  bauds  and  wish  to increase  the  baud  rate  in  steps.
From the Command mode, type 

RB U

 followed by an 

<Enter>

. The PK-232 responds with:

RBaud was 45
RBaud now 50

The RBAUD command sets the Baudot RTTY speed. The most common speed is 45 bauds
on  HF,  but  other  speeds  including  commercial  speeds  are  supported.  See  the  Command
Summary for all the supported speeds.

6.5.2

Entering Your Auto-AnswerBack

Baudot RTTY allows you to request the identity of the station you are conversing with by
sending your PK-232 the <CTRL-E> character. This causes the PK-232 to send a FIGS-D
request to the other station.

For this reason, you should set your own Auto-AnswerBack (AAB) message to either "DE
YOUR-CALL"  or  "QRA  YOUR-CALL".  See  the  Command  summary.  If  you  then  turn  your
own WRU command, your PK-232 will automatically respond by sending the AAB message
when another station requests your identity in Baudot and then stops sending.

6.5.3

Formatting Your Transmitted and Received Text

The default configuration of the PK-232 RTTY parameters are designed for natural conver-
sation and traffic. Sometimes it is desired to alter how your typed text looks on the screen
of the station you are talking to. The commands ACRRTTY and ALFRTTY allow for custom-
izing the Carriage Return and Linefeed characters in your transmitted text.

To  allow  for  changing  how  received  text  is  displayed  on  your  screen  or  printer,  see  the
ACRDISP and ALFDISP commands in the Command Summary.

MARS operators have some special requirements for RTTY operation and displaying text.
To  accommodate  these,  the  CRADD  and  MARSDISP  commands  are  included  and  should
be reviewed in the Command Summary.

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов