Timewave PK-232MBX Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 231

background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-41

166

FRI

ck "n/n"

Default: 0/0 (0 sec.)

Mode: Packet

Host: FF

Parameters:

"n" - 0 to 250, specifying the Frame Acknowledgment timeout for Meteor Scatter

work in 10 milli-second intervals.

FRICK is a short version of FRACK, meant to be used in Packet-Radio meteor scatter work. If
FRICK is 0 (default), the FRACK timer is then in use and the unit operates as before with the retry
timer in units of whole seconds. If FRICK is 1 to 250, FRICK overrides FRACK as the unit's retry
timer, and the retry timer is in units of 10 msec. up to 2500 mode. (2.5 seconds).

Unlike FRACK, FRICK does not take into account the number of digipeaters in the connect path.
FRICK assumes there are no digipeaters being used.

Note:

Do  not attempt  multiple  packet  connections  while  FRICK  is  active  (1-250).  In  con-
trast to FRACK, which provides one retry timer per multi-connect channel, there  is
only  one  FRICK  timer  in  the  PK-232.  Each  logical  channel  will  try  to  use  the  same
FRICK timer, causing interference to the operation of the other channels.

Due to the sporadic nature of meteor scatter work, a Master/Slave mode can be enabled in the PK-
232 with User BIT 18 (UBIT 18). When UBIT IS OFF, Frame Acknowledge operation is as in pre-
vious firmware versions.

When UBIT 18 is ON, a master/slave relationship is established in Packet-Radio connections. This
is done to reduce the possibility of simultaneous transmissions by both sides of a packet connec-
tion. In this mode, the master station sends either an I-Frame or a polling frame upon the expira-
tion of FRICK (or FRACK if FRICK = 0). The FRICK or FRACK timer then starts counting again. The
master station therefore sends packets constantly, even if all its I-frames have been acknowl-
edged. The slave station sends nothing, not even I-frames, until it receives a polling frame from
the master. A station becomes the master upon its transmission of a SABM (connect) frame; a sta-
tion becomes the slave upon its transmission of a UA (acknowledgement of the SABM) frame.

Recommended settings for this method of meteor scatter work (both stations should use these
settings):

UBIT IS ON
RETRY 0
AX25L2V2 ON (default)
MLXFRAME 1
(CHECK doesn't matter)
FRICK n

where n is large enough to allow the other station time to send the start of
an acknowledgement frame

Note:

This is an experimental mode and we welcome any comments or suggestions you
might have. Please make them in writing and direct them to the Timewave Engi-
neering Department. Thank You.

FS

peed "n"

Default: 2 (120)

Mode: FAX

Host: FS

Parameters:

"n" -

0 to 4 selects the FAX horizontal scan rate from the table below:

«
...
164
165
166
167
168
...
»

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

Бренд: Abus Страницы: 60

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: Juniper Страницы: 502

Бренд: peplink Страницы: 2

Бренд: Schrack Technik Страницы: 2

Бренд: Juniper Страницы: 7

Бренд: Ravpower Страницы: 27

Бренд: B&B Electronics Страницы: 2

Бренд: Asante Страницы: 150

Бренд: Cisco MERAKI Страницы: 4

Бренд: YATO Страницы: 96

Бренд: ActionTec Страницы: 115

Бренд: eWON Страницы: 34

Бренд: ADTRAN Страницы: 20

Бренд: Lanner Страницы: 141

Бренд: DPS Telecom Страницы: 80

Бренд: Matrix Switch Corporation Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды