Timewave PK-232MBX Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 231

background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-59

184

MYM

ail call[-"n"]

Default: none

Mode: Packet/MailDrop

Host: Me

Parameters:

call -

The Call Sign you wish to use for the MailDrop.

"n" -

Numeral indicating an optional substation ID (SSID) or extension.

"Call" is the call sign of the MailDrop, default: none.

"Call" may have an optional SSID, and must not be the same call sign and SSID as MYCALL. If you
do not set MYMAIL, the MailDrop will use the same call sign and SSID as entered in MYCALL. For
example, if you have set MYCALL to N7ML then MYMAIL may be N7ML-1 through N7ML-15. You
can use the CTEXT and MTEXT messages to inform other stations who connect of your MYCALL
and MYMAIL call signs.

MYPT

call callsign

Default PK232

Mode: Pactor

Host: Mf

Use the MYPTCALL command to load your call sign Into your PK-232.

If you have not loaded a call into the PK-232 with MYPTCALL, the call loaded in MYCALL will be
used. The difference between MYCALL and MYPTCALL is that MYCALL allows only the dash (-) to
be used while MYPTCALL will allow any punctuation with the call.

If calls have not been loaded into either MYCALL or MYPTCALL, the PK-232 will not allow transmis-
sion on Pactor. An error message "Need MYCALL" will be displayed if transmission is attempted.

Example:

MYPTCALL K6RFK/ZL <Enter>

MYS

elcal aaaa

Default: none

Mode: AMTOR

Host: MG

Parameters:

aaaa - Specifies your SELective CALling code (SELCALL)

Use the MYSELCAL command to enter the SELCALL (SELective CALLing) code required in AMTOR
ARQ (Mode A) and SELFEC operating modes. MYSELCAL is a unique character string which must
contain four alphabetic characters and is normally derived from your call sign.

Amateurs may simply enter their callsign and the PK-232 will automatically translate it to a 4-char-
acter SELCALL using the grouping table below:

GROUP

CALL

SELCALL

1 by2

W1XY

WWXY

1 by3

W1XYZ

WXYZ

2 by1

AB1X

AABX

2 by2

AB1XY

ABXY

2 by3

KA1XYZ

KXYZ

Although the convention is to form the SELCALL from the call sign, your PK-232 can include any
AMTOR character in the SELCALL. In accordance with CCIR Recommendation 491, four- or five-dig-
it numbers may be entered; the PK-232 automatically translates the numeric entry to your four-let-
ter alpha SELCALL.

«
...
182
183
184
185
186
...
»

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

Бренд: ABB Страницы: 66

AirPlus DWL-810

Бренд: D-Link Страницы: 25

EtherLink 3C509B

Бренд: 3Com Страницы: 8

Бренд: Icidu Страницы: 10

Network Space MAX

Бренд: LaCie Страницы: 2

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: APM Страницы: 3

Бренд: Patton electronics Страницы: 23

Бренд: Lancom Страницы: 102

Бренд: Edgewater Networks Страницы: 7

Бренд: Schrack Technik Страницы: 2

LMP-1202M-SFP Series

Бренд: ANTAIRA Страницы: 2

Бренд: FOR-A Страницы: 2

Бренд: Hunter Страницы: 2

Бренд: SriHome Страницы: 12

Бренд: JLCooper Electronics Страницы: 12

Бренд: ADDON Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды