Timewave PK-232MBX Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 231

background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-19

144

A

x25l2v2 ON|OFF

Default: ON

Mode: Packet

Host: AV

Parameters:

ON -

The PK-232 uses AX.25 Level 2 Version 2.0 protocol.

OFF - The PK-232 uses AX.25 Level 2 Version 1.0 protocol.

This command allows the selection of either the old (version 1) version of the AX.25 packet proto-
col or the current (version 2.0) protocol. Some implementations of version 1 of AX.25 protocol
won't properly digipeat Version 2.0 AX.25 packets. Most users run AX.25 version 2 but this com-
mand allows returning to the older version if necessary for compatibility.

AXD

elay "n"

Default: 0 (00 msec.)

Mode: Packet

Host: AX

Parameters:

"n" -

0 to 180 specifies a key-up delay for voice repeater operation in ten-milli-
second intervals.

AXDELAY specifies the period of time the PK-232 will wait – in addition to the delay set by TXDE-
LAY – after keying the transmitter and before data is sent. Packet groups using a standard "voice"
repeater to extend the range of the local area network may need to use this feature.

Repeaters with slow electromechanical relays, auxiliary links (or other circuits which delay trans-
mission after the RF carrier is present) require more time to get RF on the air. Try various values to
find the best value for "n" if you're using a repeater that hasn't been used for packet operations
before. If other packet stations have been using the repeater, check with them for the proper set-
ting. AXDELAY acts together with AXHANG.

AXH

ang "n"

Default: 0 (000 msec.)

Mode: Packet

Host: AH

Parameters:

"n" -

0 to 20 specifies voice repeater "hang time" in 100-millisecond intervals.

AXHANG allows you to increase efficiency when sending packets through an audio repeater that
has a hang time greater than 100 milliseconds.

When the PK-232 has heard a packet sent within the AXHANG period, it does not add the repeater
keyup delay (AXDELAY) to the key-up time. Try various values to find the best value for "n" if you
are using a repeater that hasn't been used for packet operations before. If other packet stations
have been using the repeater, check with them for the proper setting.

BA

udot

Immediate Command

Mode: Command

Host: BA

BAUDOT is an immediate command that switches the PK-232 into the Baudot mode. Baudot RTTY
operation is very common around the world, and is the basis of the telex network and most radio
press, weather and point-to-point message services. The Baudot/Murray and ITA #2 character sets
do not contain lower case or the special punctuation and control characters found in ASCII. Be-
cause the Baudot/ITA #2 code requires only five information bits to define each character, it will
generally suffer fewer errors than ASCII code at the same data rate.

«
...
142
143
144
145
146
...
»

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

Бренд: Observint Страницы: 11

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

Бренд: ADTRAN Страницы: 9

Бренд: ForeScout Страницы: 28

Бренд: Stephen Страницы: 102

Бренд: I-O Wireless Страницы: 55

Бренд: Far Tools Страницы: 24

Бренд: Keithley Страницы: 98

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: IMC Networks Страницы: 36

Бренд: Tripp Lite Страницы: 2

Бренд: ACTi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды