manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 117 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 117

PK-232 MBX – OPERATING MANUAL

PACTOR OPERATION

2/93

11-5

117

from  PHASING  to  IDLE,  you  will  see  a  CONNECTED  message  on  your  screen.  You
may then begin your conversation.

N7ML DE (

YOURCALL

) ... etc.

o

When you finish typing your comments or traffic to the other station and wish the
distant  station  to  transmit  to  you  will  need  to  type 

KKK

  or 

BTU

  to  let  the  other

station know that you are going to change the link direction.

o

Then, type a 

<CTRL-Z>

 (Hold the "CTRL" key down while typing the Z) to turn the

link over to the other station.

<CTRL-Z>  is  the  character  defined  by  the  PTOVER  command  that  switches  your
system from being the Information Sending Station (ISS) to the Information Receiv-
ing Station (IRS) and switches the distant system from being the information receiv-
ing station to the information sending station. This single character operates like the
"+?" does in AMTOR.

The FCC requires station identification once every ten minutes. It's sufficient to begin with
"QRA  (

mycall

)"  or  end  your  transmission  with  "QRA  (

mycall

)"  before  the  "<CTRL-Z>"

changeover,  or  use  the  <CTRL-B>  "HERE-IS"  to  send  your  own  Auto-AnswerBack  mes-
sage. For the "HERE-IS" command to function, you must have your AAB text entered. See
appendix A for the AAB command.

11.6.3.1

Ending An ARO Pactor Contact

When  you've  finished  your  "final  finals",  to  the  distant  station  and  both  stations  are
ready to end the Pactor ARQ contact, you can end the contact and terminate the link in
several different ways:

o

Type 

<CTRL-D>

  to  stop  sending  after  the  transmit  buffer  is  empty.  <CTRL-D>

breaks the link and returns your PK-232 to Command Mode in Pactor Standby. This
is the best way to end a Pactor contact.

o

Type 

<CTRL-F> 

to stop sending after the transmit buffer is empty, send your Morse

ID,  and  return  to  Pactor  Standby  and  Command  Mode.  Transmitter  and  returns  to
Pactor  Standby  and  Command  Mode.  This  is  the  best  way  to  end  a  contact  if  you
want to identify your station in Morse code as well.

o

Wait  until  all  the  text  has  been  sent,  then  type 

<CTRL-C>

  to  return  to  Command

Mode,  then  type 

R

  to  break  the  link.  The  PK-232  will  then  go  into  the  Pactor

Standby mode.

o

Type 

<CTRL-C>

  to  return  to  Command  Mode,  then  type 

R<Enter>  R<Enter>

  to

break  the  link  immediately.  If  there  are  characters  left  in  the  transmit  buffer,  they
will not be sent. This method should onlv be used for an emergency shutdown as it
does not send the control signal to the other station that informs it you are shutting
down. As a result the other station will continue to send until it's internal timer turns
it off.

11.6.4

Long Path Contacts

If the station you are going to call is more than half way around the earth i.e. a long path
contact,  precede  that  station's  callsign  with  an  exclamation  point.  The  will  change  the
Pactor timing to allow for the extended radio propagation delay. You would type:

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов