manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации


Поделиться
Скачать
background image

PK-232 MBX – OPERATING MANUAL

COMPUTER INSTALLATION

4/91

2-3

18

2.3

Connecting Your Computer or Computer Terminal

MAKE SURE THE PK-232 AND YOUR COMPUTER ARE SWITCHED OFF

o

Locate  the  PK-232  Serial  Cable.  Connect  the  25-pin  Male  connector  to  the  RS-232
I/O connector on the rear of the PK-232. If you are not using an AEA RS-232 cable,
make  sure  that  the  cable  you  are  using  has  no  other  pins  than  1-8  and  20  con-
nected.

o

Connect  the  other  end  of  this  cable  (Female  DB-25)  to  the  RS-232  Serial  Port  of
your  personal  computer  or  Computer  Terminal.  Details  on  connecting  to  common
machines are listed below.

NOTE:

This  cable  was  designed  to  connect  directly  to  a  25-pin  IBM-PC  compatible
RS-232  port.  Many  machines  on  the  market  today  support  this  configuration.
Some  less-common  machines  are  listed  in  section  2.6.  Please  make  certain
you  have  properly  connected  the  PK-232  to  your  RS-232  computer  or  Com-
puter Terminal then proceed to section 2.4.

2.3.1

IBM-PC/XT/AT and Compatibles

IBM  compatible  25-pin  RS-232  serial  ports  should  connect  directly  to  the  supplied  serial
cable.  Some  IBM  compatible  machines  are  equipped  with  a  9-pin  serial  port.  For  these
machines  a  DB-9  to  DB-25  adapter  should  be  obtained  from  a  Radio  Shack  store  or  a
computer dealer.

2.3.2

Apple Macintosh Series of Computers

Timewave  does  not  sell  a  terminal  program  for  Apple  computers.  A  few  third-party  pro-
grams are available and can be found by searching the World Wide Web.

2.3.3

Computer Terminal

If you have an RS-232 Computer Terminal, sometimes called a Dumb-Terminal, Smart-Ter-
minal or ASCII-Terminal, you may need to change the gender of the cable provided with
your PK-232. This can be accomplished with an inexpensive double-male RS-232 gender
changing  adapter  available  from  Radio  Shack  and  other  computer  dealers.  The  Radio
Shack part number is 26-243.

2.4

Setting Up Your Communications or Terminal Software Program

If you will be using your PK-232 with a Computer, you will need to read parts of this section
to set up your Communications or Terminal Program Software. If you will be using your PK-
232 with a Computer Terminal you will not need any software and may skip to section 2.5.   

Setting up a Communications program for your PK-232 is very important.

How your screen looks when you use your PK-232 depends completely on your Communica-
tions program. AEA currently makes available programs for the IBM-PC and compatibles, the
Apple Macintosh and the Commodore 64/128 computers. These products are customized for
radio communications and are available at extra cost from your AEA dealer.

The PK-232 operates in much the same manner as a telephone modem and most telephone
modem  Terminal  Programs  will  control  a  PK-232  quite  nicely.  Some  of  these  programs  are
"Public  Domain"  which  means  they  are  FREE.  Other  Terminal  Programs  are  "Share-ware"
which means you may get them from a friend and try them before you buy them. Whether

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

D-Link AirPlus DWL-810 Owner'S Manual preview
AirPlus DWL-810
Бренд: D-Link Страницы: 25
Google AC-1304 User Manual preview
AC-1304
Бренд: Google Страницы: 14
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Бренд: Paradyne Страницы: 6
TwinMOS Octopus G Series User Manual preview
Octopus G Series
Бренд: TwinMOS Страницы: 29
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Бренд: axing Страницы: 52
Dialogic Media Board D/120JCT-LS-EW Installation Manual preview
Media Board D/120JCT-LS-EW
Бренд: Dialogic Страницы: 2
MiWire SeaWire Pro User Manual preview
SeaWire Pro
Бренд: MiWire Страницы: 24
i-MO OptiBond 210 C Series Hardware Installation Manual preview
OptiBond 210 C Series
Бренд: i-MO Страницы: 16
ZyXEL Communications P-660R-TX V3 Support Notes preview
P-660R-TX V3
Бренд: ZyXEL Communications Страницы: 66
Telestar DIGIBIT R1 Operating Manual preview
DIGIBIT R1
Бренд: Telestar Страницы: 16
NETGEAR MA 301 Reference Manual preview
MA 301
Бренд: NETGEAR Страницы: 20
Option Audio GlobeSurfer X-1 User Manual preview
GlobeSurfer X-1
Бренд: Option Audio Страницы: 30
Goonas LC180 User Manual preview
LC180
Бренд: Goonas Страницы: 13
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Бренд: Alcatel-Lucent Страницы: 8
NETGEAR DGN2200M - Wireless-N 300 Router User Manual preview
DGN2200M - Wireless-N 300 Router
Бренд: NETGEAR Страницы: 95
JETWAY FDF13 Series Quick Installation Manual preview
FDF13 Series
Бренд: JETWAY Страницы: 15
Belkin F5D7230au4P Manual preview
F5D7230au4P
Бренд: Belkin Страницы: 2
Epson USB User Manual preview
USB
Бренд: Epson Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды