manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 196 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 196

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-71

196

RFR

ame ON|OFF

Default: OFF

Mode: Baudot and ASCII RTTY

Host: RG

Parameters:

ON -

Check received Baudot and ASCII characters for framing errors.

OFF - Print received Baudot and ASCII characters regardless of errors.

When RFRAME is OFF (default), Baudot and ASCII modes operate as always, that is characters are
copied based on the presence of the DCD signal.

When RFRAME is ON, the PK-232 checks received Baudot and ASCII characters for framing errors.
A framing error on a character in an asynchronous mode (such as Baudot and ASCII) occurs when
the bit in the stop position is detected to be the wrong polarity (the polarity of the start bit is sup-
posed to be space or 0, while the stop bit is supposed to be mark or 1). The unit stops copying
characters when 4 out of the last 12 characters had framing errors. Copy resumes when the most
recent 12 characters are error-free. This should significantly reduce the copying of garbage charac-
ters when no signals are present. When RFRAME is ON, characters are copied based on the recent
history of framing errors.

RXR

ev ON|OFF

Default: OFF

Mode: Baudot and ASCII RTTY/AMTOR

Host: RX

Parameters:

ON -

Received data polarity is reversed (mark-space reversal).

OFF - Received data polarity is normal.

Use the RXREV Command to invert the polarity of the data demodulated from the received mark
and space tones.

In some cases, you may be trying to copy a station that's transmitting "upside down" although it is
receiving your signals correctly. This is especially true when listening to signals in the Short Wave
bands. Set RXREV ON to reverse the data sense of received signals.

RXREV operates only at RBAUD and ABAUD speeds up to 150 baud.

SA

mple "n"

Immediate Command

Mode: Command

Host: SA

Parameters:

"n" -

20 to 255 specifies the sampling rate in baud.

This is a new operating mode with the Summer 1991 PK-232 firmware release for advanced users
interested in decoding unknown synchronous data transmissions.

SAMPLE is similar to the SBIT and 6BIT modes, but operates on synchronous data, whereas 5B1T
and 6BIT are used on signals known to be asynchronous. SAMPLE syncs up on any regularly-paced
data  transmission  and  samples  the  data  once  per  bit,  packaging  the  data  in  groups  and  sending
the groups to the user for further analysis. The user can use SAMPLE to capture data bits from a
synchronous transmission, such as FEC, TDM or an 'unknown model' not identified by the SIGNAL
command. The transmission is actually sampled several times per data bit. The PK-232 does a ma-
jority vote an the last few samples to represent the value of the data bit.

One use for the SAMPLE command is to record the output to a disk file, then write a program to
analyze the results for synchronous/asynchronous, bit sync patterns, data decoding, etc.

SAMPLE data is captured in 6-bit units; the order of bit reception is MSB first, LSB last. The TNC
sends  the  data  unit  to  the  user  with  a  constant  of  hex  30  added  to  each  unit,  the  same  as  the

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов