background image

PK-232 MBX – OPERATING MANUAL

PACKET-RADIO

4/91

4-18

53

4.4.7.3

Redisplay

If you have erased and retyped lots of characters, you may want to see "fresh" input,
especially if BKONDEL is OFF. This will also allow you to display any packets you might
have  received  while  you  were  typing.  Your  PK-232  will  show  the  line  you're  entering
when you type the REDISPLAY character (default <CTRL-R>).

4.4.7.4

The PASS Character

If  you  are  terminal  or  terminal  program,  the  following  may  be  useful.  Sometimes  you
may want to include a special input character such as a Carriage Return (the SENDPAC
character) in a packet. For example, to send several lines in the same packet, you must
include <CR> at the end of each line. You can include any character in a packet (includ-
ing  all  special  characters)  by  prefixing  that  character  with  the  PASS  character
<CTRL-V>:

I wasn't at the meeting.<CTRL-V><CR>
What happened?

Without  the  PASS  character,  this  message  would  go  out  as  two  packets.  By  prefixing
the first <CR> with <CTRL-V>, you send it all at once, while maintaining the <CR> as
part of the text. The PASS character can be useful in formatting text Messages such as
CTEXT as well.

4.4.8

Packet Transmit Timing

Your PK-232 has a number of built-in timers used to control the Packet protocol and trans-
mit timing. The default values have been set at the factory to provide reasonable perform-
ance, but the values may not be optimum for your local area. Most protocol parameters
should be adjusted only after carefully reading about them later in the chapter.

You SHOULD adjust TXDELAY for your transmitter as indicated below.

4.4.8.1

TXDELAY and AUDELAY

Radios vary in the time it takes to switch from receive to transmit. If your PK-232 starts
sending  data  before  your  transmitter  is  up  to  power,  the  packet  will  not  be  received
properly at the distant end.

TXDELAY controls the delay between your transmitter's key-up and the moment when
your PK-232 starts sending data. The default value of 30 corresponds to a time of 300
mSec and works with most VHF/UHF FM transceivers. With modern transceivers TXDE-
LAY  can  often  be  reduced  which  will  improve  packet  performance  in  your  area.  You
should perform the following procedure to optimize TXDELAY for your station.

o

Find another station who can reliably digipeat your signals.

o

Set  your  UNPROTO  path  to  TEST  via  the  callsign  of  the  station  who  can  digipeat
your signals.

o

Set the MONITOR command to at least 1.

o

Go to CONVERSE mode and send a few packets by pressing the 

<Enter>

 key. Note

that  you  should  see  them  on  your  own  screen  when  they  are  digipeated  by  the
other station.

Содержание PK-232MBX








































































































































































































































Отзывы: