manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 208 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 208

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-83

208

WHY

not ON|OFF

Default: OFF

Mode: Packet

Host: WN

Parameters:

ON -

The PK-232 generates a reason why received packets were not displayed.

OFF - This function is disabled.

During  packet  operation,  the  PK-232  may  receive  many  packets  that  are  not  displayed.  Turning
WHYNOT on will cause the PK-232 to display a message explaining the reason the received packet
was not displayed to the screen. The messages and their meanings are shown below:

PASSALL:

The received packet frame had errors, and PASSALL was off, preventing the
packet from being displayed to the screen.

DCD Threshold:

The Threshold control was set too far counter clockwise. The DCO LED was
off when the packet was received.

MONITOR:

The MONITOR value was set too low to receive this frame.

MCON:

MCON was set too low to receive this type of frame.

MPROTO:

MPROTO was set to off, and the received packet was probably a NET/ROM or
TCP/IP frame.

MFROM/MTO:

The frame was blocked by the MFROM or MTO command.

MBX:

The  call  sign  of  the  sending  station  does  not  match  the  call  sign  setting  in
the MBX command.

MBX Sequence:

The frame was received out of sequence, probably a retry.

Frame too long:

Incoming packet frame longer than 330 bytes. Probably a non-AX.25 frame.

Frame too short:

Incoming  packet  frame  shorter  than  15  bytes.  Only  seen  if  PASSALL  ON.
Probably noise.

RX overrun:

Another HDLC byte was received before we could read the previous one out
of the HDLC chip.

W

ideshft ON|OFF

Default: OFF

Mode: Baudot/ASCII RTTY/AMTOR/Pactor Host: WI

Parameters:

ON -

RTTY tones are shifted 1000 Hz.

OFF - RTTY tones are shifted 200 Hz (emulates 170-Hz shift).

The WIDESHFT command permits the use of the PK-232 on VHF or HF with either wide (1000 Hz)
or narrow (200 Hz) shifts. Many amateur radio VHF and HF RTTY operators use 170 Hz shift. The
PK-232's 200 Hz shift is well within the filter tolerances of any RTTY demodulator in general serv-
ice.  MARS  stations  will  find  WIDESHFT  generally  compatible  with  MARS  and  commercial  850  Hz
shift RTTY operations.

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов