manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 159 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 159

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-34

159

FSK  (two-tone)  operation,  in  both  receive  and  transmit.  WIDESHFT,
RXREV and TXREV are active.

Bit 9, position $0200:

Bit position 9 does for AMTOR what WRU does for Baudot and ASCII.
If bit 9 is set to 1 (default), a FIGS-D in ARQ causes the unit to be-
come the ISS, transmit the AAB string, then revert back to the IRS. If
bit 9 is set to 0, then a received FIGS-D will have no effect.

Bit 10, position $0400:

If bit 10 is set to 0 (default), then host polling is as before. If bit 10 is
set to 1, then any change in status (e.g. Idle to Tfc) in AMTOR, FAX,
TDM or NAVTEX causes the PK-232 to issue the following host block:

SOH $50 n ETB

where  n  is  $30-36,  the  same  number  that  the  OPMODE  command
furnishes. This block is subject to HPOLL.

Bit 11, position $0800:

If bit 11 is set to 1 (default), a connected message appears when an
ARQ  link  is  first  established  using  seven-character  SELCALLs  (CCIR
625). If bit 11 is set to 0, no connected message appears at the be-
ginning of ARQ communications.

Bit 12, position $1000:

If bit 12 is set to 0 (default), the Packet Morse ID (MID) is on/off key-
ing  of  the  low  tone.  If  bit  12  is  set  to  1,  the  Morse  ID  is  sent  in  2-
tone FSK with the low tone being key-down and the high tone repre-
senting key-up. Use this setting to keep other stations from sending a
packet during the Morse ID.

Bit 13, position $2000:

If bit 13 is set to 0 (default), MailDrop connect status messages are
always sent to the local user, regardless of the setting of MDMON. If
bit  13  is  set  to  1,  remote  user  dialog  and  connect  status  messages
with the MailDrop are shown only if MDMON is ON.

Bit 14, position $4000:

If  bit  14  is  set  to  0  (default),  the  transmit  buffer  for  data  sent  from
the  computer  to  the  PK-232  in  Packet  mode  is  limited  only  by  avail-
able PK-232 memory. If bit 14 is set to 1, the serial flow control will
permit only a maximum of 7 I-frames to be held by the PK-232 before
transmission. This solves a problem with the YAPP binary file transfer
program which relies on a small TNC transmit buffer to operate  cor-
rectly.

Bit 15 is unused at the present time. To return CUSTOM to the default setting, type 

CU Y

 or 

CU ON

at the command prompt.

CW

id "n"

Default: $06 <CTRL-F>

Mode: Baudot/ASCII RTTY/AMTOR/FAX

Host: CW

The CWID command lets you change the "send CWID" control character typed at the end of your
Baudot and ASCII RTTY dialogue.

When the PK-232 reads this character embedded in the text or keyboard input, it switches modes
and sends your call sign in Morse code, at the keying speed set by MSPEED. As soon as your call
sign has been sent in Morse, the PK-232 turns off your transmitter and returns to receive.

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов