Timewave PK-232MBX Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 231

background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-64

189

PASSALL turns off the PK-232's packet error-detecting mechanism and displays received packets
with invalid CRCS. PASSALL is normally turned OFF (default); which ensures that packet data la er-
ror-free by rejecting packets with invalid CRC fields. When PASSALL is ON, packets are displayed,
despite CRC errors. The MHEARD logging is disabled since the call signs detected may be incor-
rect.

PE

rsist "n"

Default: 63

Mode: Packet

Host: PE

Parameters:

"n" -

0 to 255 specifies the threshold for a random attempt to transmit.

The PERSIST parameter works with the PPERSIST and SLOTTIME parameter to achieve true p-per-
sistent CSMA (Carrier-Sense Multiple Access) in Packet operation.

PK

"n"

Default: none

Mode: All

Host: PK

Parameters:

"n" -

a hex number used to access the PK-232's memory and I/O locations.

PK (Peek/Poke) permits access to memory locations. To use the PK command:

o

Set the memory address into the ADDRESS command.

o

Use the PK command without arguments to read that memory location.

o

Use PK with one argument O-$FF to write to that memory location.

PK-232 RAM locations are $8000-$FFFF. ROM begins at $0000. This command is used primarily as
a programmer's aid and is not needed for normal PK-232 use.

PP

ersist ON|OFF

Default: ON

Mode: Packet

Host: pp

Parameters:

ON -

The PK-232 uses p-persistent CSRA (Carrier Sense Multiple Access).

OFF - The PX-232 uses DWAIT for TAPR-type 1-persistent CSMA.

When PPERSIST is ON (default), the PK-232 uses the PERSIST and SLOTTIME parameters for p-
persistent CSMA instead of the older DWAIT CSMA procedure.

When your computer has queued data for transmission, the PK-232 monitors the DCD signal from
its modem. When the channel clears, the PK-232 generates a random number between 0 and 255.
If this number is less-than or equal to "PERSIST", the PK-232 transmits all frames in its queue. If
the random number is greater than "P", the PK-232 waits .01 * SLOTTIME seconds and repeats the
attempt.

PPERSIST can be used in both KISS and normal AX.25 operation.

PRC

on ON|OFF

Default: OFF

Mode: All

Host: PC

Parameters:

ON -

A parallel printer is connected to the PK-232 via the special cable.

OFF - There is no parallel printer connected, or it is not currently in use.

«
...
187
188
189
190
191
...
»

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

Бренд: Makita Страницы: 2

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

Бренд: QNAP Страницы: 39

Бренд: Usr Страницы: 2

totalstorage 200

Бренд: IBM Страницы: 152

Бренд: Allied Telesis Страницы: 1

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды