manualshive.com logo in svg

Timewave PK-232MBX, Руководство по эксплуатации, Страница: 195 / 231

Поделиться
Скачать
Timewave PK-232MBX Скачать руководство пользователя страница 195

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-70

195

RESET

Immediate Command

Mode: Command

Host: RS

RESET is an immediate command that resets all parameters to PK-232's PROM default settings and
reinitializes the PK-232.  All personalized parameters, monitor lists and MailDrop messages will be
lost.

RES

ptime "n"

Default: 0 (000 msec.)

Mode: Packet

Host: RP

Parameters:

"n" -

0 to 250 specifies 100-millisecond intervals.

RESPTIME adds a minimum delay before your PK-232 sends acknowledgment packets. This delay
may run concurrently with the default wait time set by DWAIT and any random wait in effect.

During a file transfer, RESPTIME can help avoid data/ack collisions caused by the sending stations
TNC pausing briefly between transmitted data frames.

RESTART

Immediate Command

Mode: Command

Host: RT

RESTART is an immediate command that reinitializes the PK-232 while retaining the user's settings.
The effect of the RESTART command is the same as turning the PK-232 OFF, then ON again.

RESTART does not reset the values in bbRAM. See the RESET command.

RE

try "n"

Default: 10

Mode: Packet

Host: RY

Parameters:

"n" -

0 to 15 specifies the maximum number of packet-retries.

The  AX.25  protocol  uses  the  retransmission  of  frames  that  have  not  been  acknowledged  as  a
means to insure that ALL transmitted frames are received. The number of retries that the PK-232
will attempt is set by the RETRY command (default 10). If the number of retries is exceeded, the
packet link may be lost.

RF

ec ON|OFF

Default: ON

Mode: AMTOR

Host: RF

Parameters:

ON -

Mode B (FEC) signals are displayed in AMTOR Standby (default).

OFF - Mode B (FEC) signals are not displayed in AMTOR Standby.

Turn the RFEC command OFF to prevent the reception and display of all FEC signals received while
in AMTOR Standby.

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов