Timewave PK-232MBX Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 231

background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-53

178

ME

mory "n"

Default: none

Mode: All

Host: MM

Parameters:

"n" -

A hexadecimal value used to access the PK-232's memory locations, or read
values stored at a specified ADDRESS.

The MEMORY command works with the ADDRESS command (ADDRESS $aabb) and permits access
to memory locations. Use the Memory command without arguments to read a memory, and with
one argument $0 to $FF to write to a memory location. The value in ADDRESS is incremented after
using the MEMORY command.

MFI

lter n1[,n2[,n3[,n4]]]

Default: $80

Mode: Morse, Baudot ASCII, AMTOR and Packet

Host: MI

Parameters:

"n" -

0 to $80 (0 to 128 decimal) specifies an ASCII character code.
Up to four characters may be specified separated by commas.

Use MFILTER to select up to 4 characters to be "filtered," or excluded from Morse, Baudot, ASCII,
AMTOR and monitored packets. Parameters "n1," - "n4" are the ASCII codes for the characters you
want to filter. The special value of $80 (default) filters all characters above $7F and all control-
characters except carriage-return ($0D), linefeed ($0A), and TAB ($09).

MFrom

ALL|NONE or YES/NO call1[,call2..]

Default: ALL

Mode: Packet

Host: MF

Parameters:

call -

ALL|NONE or YES_list/NO_list (list of up to eight call signs, separated by
commas).

MFROM determines what packets are monitored. To monitor all packets, set MFROM to ALL. To
stop any packets from being displayed, set MFROM and MTO to NONE.

To display packets from one or more specific stations, type MFROM YES followed by a list of call
signs you WANT to monitor packets from. To hide packets from one or more specific stations, type
MFROM NO followed by a list of call signs you want NOT to monitor packets from. When using
MFROM, set MTO to NONE.

You can include optional SSIDs specified as "-n" after the call sign. If MFROM is set to "NO N6IA,"
any combination N6IA-0,...N6IA-15 will NOT be monitored. If MFROM is set to "YES N6IA-1," then
only N6IA-1 will be monitored. When MFROM and MTO contain different arguments, the following
priority applies:

1. ALL,

2. NO_list,

3. YES_list,

4. NONE

Clear MFROM with

%

,

&

or

OFF

as arguments.

MHeard

Immediate Command

Mode: Packet/AMTOR MailDrop

Host: MH

MHEARD is an immediate command that displays a list of up to 18 most recently heard stations.
Stations that are heard directly are marked with a * in the heard log. Stations that have been re-
peated by a digipeater are not marked.

«
...
176
177
178
179
180
...
»

Содержание PK-232MBX








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-232MBX

Бренд: M2M Страницы: 9

Бренд: Garmin Страницы: 2

Бренд: iDirect Страницы: 60

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

Бренд: Oracle Страницы: 24

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: ZyXEL Communications Страницы: 299

Бренд: Far Tools Страницы: 24

Бренд: QTech Страницы: 406

Бренд: ZyXEL Communications Страницы: 3

Бренд: Fluke Страницы: 102

Бренд: Draytek Страницы: 17

Бренд: Net Optics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды