Thermo Scientific Vanquish VH-P10-A-02 Скачать руководство пользователя страница 212

Страница: 212 / 238

•

Troubleshooting

Page 212

Vanquish Pumps (VH-P10-A-02) Operating Manual

2. Take remedial action if required.

♦

Compression value lower than indicated in the table

Replace the outlet check valve.

♦

Compression value higher than indicated in the table

♦

The piston seal may be defective. Replace the piston seal.

♦

The inlet check valve may be defective. Replace the inlet

check valve.

♦

Very high compression (message "Compression limit reached"
and low pressure)

♦

Air bubbles may be present in the pump. Make sure that no

air bubbles are present in the solvent lines and then, purge

the pump.

♦

If solvent shut off valves are installed:

Verify that the valves

are open.

♦

Excessive leakage may be present on the inlet check valve.

Remove the solvent line from the solvent reservoir and the

solvent line filter from the solvent line. While the pump is

running, observe the liquid in the solvent line. If the liquid

moves also against the direction of flow during the stroke,

the inlet check valve may be defective. Replace the inlet

check valve.

Содержание Vanquish VH-P10-A-02















































































































































































































































Результаты поиска

Содержание Vanquish VH-P10-A-02

Отзывы:

Похожие инструкции для Vanquish VH-P10-A-02

Бренды по названию

Популярные бренды

Thermo Scientific Vanquish VH-P10-A-02, Руководство по эксплуатации

Результаты поиска

Содержание Vanquish VH-P10-A-02

Отзывы:

Похожие инструкции для Vanquish VH-P10-A-02

Бренды по названию

Популярные бренды