Thermo Scientific Vanquish VH-P10-A-02 Скачать руководство пользователя страница 184

Страница: 184 / 238

•

Maintenance and Service

Page 184

Vanquish Pumps (VH-P10-A-02) Operating Manual

7.15

Replacing the Doors

When

Damage of door

TIP

The maintenance procedures do not require that you remove the

doors. If this should ever be required for a specific reason or procedure,
follow the related steps in this section.

Parts required

Replacement door

Follow these steps

NOTICE

To avoid damage to the door hinges, be careful when

performing the following sequence of steps and do not apply force.

1. To remove a door, push the door upward while opening.

Open the door to a position in which the two hinges on the housing
are aligned in the grooves on the door. You can remove the door
only when the hinges are in the grooves.

Figure 71: Unhinging a door

2. Slightly tilt the door to the outside, away from the housing, and

remove the door.

3. To install the door, align the door with the hinges on the housing. Be

careful not to clamp tubing or capillaries between the door and the
enclosure.

No.

Description

Hinge on the housing

Reception groove on
the door

Содержание Vanquish VH-P10-A-02















































































































































































































































Результаты поиска

Содержание Vanquish VH-P10-A-02

Отзывы:

Похожие инструкции для Vanquish VH-P10-A-02

Бренды по названию

Популярные бренды

Thermo Scientific Vanquish VH-P10-A-02, Руководство по эксплуатации

Результаты поиска

Содержание Vanquish VH-P10-A-02

Отзывы:

Похожие инструкции для Vanquish VH-P10-A-02

Бренды по названию

Популярные бренды