Themis TA64 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 164

background image

5-4

Themis Computer

TA64 Hardware Manual

Either of these actions will transfer the content of the Limit Register into the Counter
Register and will also enable the count-down process.

Once started, a watchdog counter cannot be stopped, unless it is reset or the count-
down process has reached zero.

5.4

X-Bus (ISA) Flash

The FPGA is responsible for controlling the access of the X-Bus (ISA) Flash device
through its LPC to ISA bridge function. The CPU accesses the ISA Flash via the
LPC interface of the AMD8111 chipset. This Flash can be used as a booting device,
which holds the BIOS of the TA64 system. It can also be used as a user Flash if not
as a booting device.

A jumper (JP11) of the TA64 is used to choose the booting device. When the ISA
Flash is chosen as the booting device, it will use address range FF00.0000 --
FFFF.FFFF. When the ISA Flash is chosen as the user Flash (therefore not a booting
device), it will use the address range FC00.0000 -- FCFF.FFFF.

To summarize:

• Boot Flash: FF00.0000 -- FFFF.FFFF

• User Flash: FC00.0000 -- FCFF.FFFF

5.5

Register Description

5.5.1

Summary

Figure 5-1

summarizes of all the registers implemented in the FPGA.

Table 5-1.

TA64 FPGA Register Address Map

Register Name

Size

Address

Description

FPGA revision

8 bit

0xFB00.0000

TA64 FPGA revision

ISR control

8 bit

0xFB00.0001

On-board ISR programming control

Boot path control

8 bit

0xFB00.0002

TA64

boot path control

«
...
80
81
82
83
84
...
»

Содержание TA64





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TA64

ITX-945GC3B N330

Бренд: OEM Страницы: 38

Altera Lark Board

Бренд: Embest Страницы: 9

Бренд: Microchip Technology Страницы: 17

Бренд: JETWAY Страницы: 54

Бренд: VIA Technologies Страницы: 86

Бренд: Supermicro Страницы: 111

Бренд: Embedian Страницы: 70

D850MV - Desktop Board Motherboard

Бренд: Intel Страницы: 25

Бренд: EPOX Страницы: 83

Бренд: Yamaha Страницы: 77

Бренд: Transcend Страницы: 51

Бренд: Transcend Страницы: 51

Бренд: Systium Technologies Страницы: 5

Бренд: Maxim Integrated Страницы: 4

Бренд: Maxim Integrated Страницы: 11

Бренд: Maxim Integrated Страницы: 21

Бренд: Medion Страницы: 29

Бренд: Habey Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды