Themis TA64 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 164

background image

TA64 Hardware Manual

xviii

Themis Computer

ThemisComputer values its customer comments and opinions; therefore, a “Reader
Comment Card” is located at the end of this manual for your use. Please take the
time to fill out this card with any comments concerning Themis products and ser-
vices, and return it to Themis Computer. Your comments may also be forwarded to
Themis by sending email to

[email protected]

.

Before you begin, carefully read each of the procedures in this manual and the asso-
ciated Software manual. Serious damage can be caused by improper handling of the
equipment.

TA64 Models

The TA64 has a total of three models (see

Table 1

).

All models are based on a combination of three different VME64 boards: the TA64
Baseboard, the 2P2 PMC/XMC Carrier Board with two PMC Module slots, and the
2P3 PMC Carrier Board with three PMC Module slots. Users may obtain graphics
capability by installing a TGA-7000 PMC graphics accelerator card in an available
PMC/XMC Module slot.

Table 1.

TA64 Model Configurations

Model

a

Baseboard

TGA3D/3D+

Graphics Board

b

PMC/XMC Carrier Board

(1 only)

VME Slot 1

VME Slot 2

VME Slot 3

2 Modules

c

VME Slot 2

3 Modules

d

VME Slot 2

TA64 / 1

Yes

Not Supported

TA64 / 2P2

Yes

2P2 PMC/XMC

TA64 / 2P3

Yes

2P3 PMC

a—The TA64 does not support PCI Express; hence XMC Modules are not supported.

b—TGA3D/3D+ Graphics Boards are not supported by the TA64. Instead, a TGA-7000 PMC Graphics Card is recommended.

c—New 2P2 PMC/XMC Carrier Board (P/N 112794-001) only; the standard version 2P2 PMC Carrier Board is not compatible.

d—The standard version 2P3 PMC Carrier Board is supported.

Caution:

A new 2P2 PMC/XMC Carrier Board has been designed to operate with

the TA64 system, which does not support the original 2P2 PMC Carrier Board. DO
NOT ATTEMPT to operate the original 2P2 PMC Carrier Board with the TA64.

«
...
16
17
18
19
20
...
»

Содержание TA64





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TA64

Бренд: MPS Страницы: 6

Бренд: PC Partner Страницы: 20

Бренд: IEI Technology Страницы: 17

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

Бренд: Emcore Страницы: 12

PCAN-MicroMod Evaluation Kit

Бренд: Peak Страницы: 18

Бренд: EVGA Страницы: 14

Бренд: Microchip Technology Страницы: 31

Бренд: Silicon Laboratories Страницы: 18

Бренд: Gigabyte Страницы: 44

Бренд: MSI Страницы: 445

Бренд: JETWAY Страницы: 48

PHANTOM GAMING B650E PG-ITX WiFi

Бренд: ASROCK Страницы: 62

Бренд: Hochiki Страницы: 8

M3A78-CM - Motherboard - Micro ATX

Бренд: Asus Страницы: 96

Бренд: Asus Страницы: 116

Бренд: Asus Страницы: 60

Бренд: Asus Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды