Themis TA64 Скачать руководство пользователя страница 101

Страница: 101 / 164

A-5

Themis Computer

A—Connector Pinouts and LED Indicators

TA64 Front-Panel Connectors

A.1.3

Gigabit Ethernet (GBE) Port A

Connector Type:

RJ45 GBE Connector with Transformer, 8 Pin, 2 LEDs

Manufacturer; Part Number:

AMP/Tyco; 1605814-5

The Ethernet port is an RJ45 (10-pin; 8-pin external) GBE connector with two
embedded LEDs (see

Figure A-3

and

Table A-3

below) supporting 10/100/

1000Base-T transmission. This specialized connector also has an embedded trans-
former for signal conversion.

Figure A-3.

Gigabit Ethernet RJ45 Connector Pinout

Symbol

Baseboard

Link Speed LED

Network Traffic LED

Pin 3

Pin 1 = Ground
Pin 2 = Vcc

Table A-3.

Gigabit Ethernet Connector-Pin Signals and LED Interpretation

Pin

Signal

Description

LED

Flash Rate

Interpretation

GND

Chassis ground

Yellow
(

Top

)

= Link
Speed

ON-ON-ON-ON-OFF-ON-
OFF

10 Mb/s

Vcc

Voltage supply

MX3+

Transmit/Receive MX3+

ON-ON-ON-ON-OFF-ON-
OFF-ON-OFF

100 Mb/s

MX3–

Transmit/Receive MX3–

ON-ON-ON-ON-OFF-ON-
OFF-ON-OFF-ON-OFF

1000 Mb/s

MX2+

Transmit/Receive MX2+

Green
(

Bottom

)

= Network
Traffic

Flashing rate is 300 ms for each transmission/
receive activity.

MX2–

Transmit/Receive MX2–

MX1+

Transmit/Receive MX1+

MX1–

Transmit/Receive MX1–

MX0+

Transmit/Receive MX0+

a. “ON” means the LED is on for 300 ms.
“OFF” means the LED is off for 300 ms.

MX0–

Transmit/Receive MX0–

Содержание TA64





































































































































































Результаты поиска

Содержание TA64

Отзывы:

Themis TA64, Руководство по оборудованию, Страница: 101 / 164

Результаты поиска

Содержание TA64

Отзывы: