manualshive.com logo in svg

Themis TA64, Руководство по оборудованию, Страница: 88 / 164

Поделиться
Скачать
Themis TA64 Скачать руководство пользователя страница 88

5-10

Themis Computer

TA64 Hardware Manual

5.5.7

On-Board IO Setting Register

The On-Board IO Setting register reflects the settings of jumper pins and solder
beads (see Appendix B, “Jumper Pins and Solder Beads”) on the TA64 baseboard.  

Table 5-7.  

On-Board IO Setting Register 0xFB00.0005

field

Bit

Access

Description

Status of JP7

Bit 0

RO

AC97_ON_P2_L

0 = AC97 interface with P2 paddle card.

1 = AC97 interface with PMC carrier board.

Status of SB20

Bit 1

RO

TTYB_RS_232_422

0 = TTY-B set to RS422 mode.

1 = TTY-B set to RS232 mode.

Status of SB13

Bit 2

RO

SER_AB_P2_SEL

0 = TTY A/B access from front panel.

1 =TTY A/B access from P2 paddle card.

Status of SB10

Bit 3

RO

KBM_ON_P2_L

0 = PS2 keyboard/mouse access from P2 paddle card.

1 = PS2 keyboard/mouse access from front panel.

Status of SB18

Bit 4

RO

PS2_USB_SEL

0 = Provide PS2 keyboard/mouse to the front panel DIN connec-
tor.

1 = Provide 2 USB ports to the front panel DIN connector.

Status of LPC 
ROMBO

Bit 5

RO

ROMBO_SENSE_L

0 = There is no LPC ROMBO connected to the TA64 board.

1 = There is an LPC ROMBO connected to the TA64 board.

Status of SB21

Bit 6

RO

SEL_BATTLE_MODE

0 = Normal Thermal control mode.

1 = Battle Thermal control mode.(The TA64 board will not shut-
down even in the over temp condition)

SMBUS1 enable

Bit 7

RW

SMBUS1 enable control

0 = Do not allow the CPU to access the device on the SMBUS1

1 = Allow the CPU to access the device on the SMBUS1.

@ reset: 1

Note:

It is useful to have this control, since during DVT this bus 

can be accessed from external I2C controller. Thus, we should 
avoid a multi-I2C master condition.

 

Содержание TA64





































































































































































Отзывы:

Нет отзывов