Themis TA64 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 164

Themis TA64 Скачать руководство пользователя страница 50

TA64 Hardware Manual

3-2

Themis Computer

3.1.2

HyperTransport Technology

The AMD 8000 HyperTransport core-logic chipset series was designed to enhance
high-speed AMD processors—including the Turion64—and includes the AMD
8131 HyperTransport PCI-X Tunnel and the AMD 8111 HyperTransport I/O Hub.

3.1.2.1 AMD 8131 HyperTransport PCI-X Tunnel

The AMD 8131 HyperTransport PCI-X Tunnel is a high-speed device that provides
two independent, high-performance PCI-X bus bridges that are integrated with a
high-speed HyperTransport technology tunnel. Tunnelling provides the capability to
connect with other HyperTransport technology devices that are downstream (see

Figure 3-1

); namely, the AMD 8111 (see next section) in the TA64.

Major features of the AMD 8131 include the following:

• 16-bit HyperTransport interface (Side A) with a 6.4-GB/s maximum bandwidth.

• 8-bit HyperTransport interface (Side B) with a 3.2-GB/s maximum bandwidth.

• Two PCI-X bridges (Bridge A, Bridge B) that support the following features:

—PCI-X modes and legacy PCI revision 2.2 modes

—133-MHz, 100-MHz, 66-MHz, and 33-MHz transfer rates in PCI-X mode

—66-MHz and 33-MHz PCI 2.2 modes

—Independent transfer rates and operational modes for each bridge

—Support for up to five PCI masters on each bridge

Figure 3-1.

AMD 8131 HyperTransport PCI-X Tunnel

AMD 8131 HyperTransport

PCI-X Tunnel

Turion64

AMD 8111

TM

TM

Tunnel

16-bits Upstream

16-bits Downstream

8-bits Upstream

200 MHz

800 MHz

8-bits Downstream

Side B

Side A

PCI-X

Bridge A

PCI-X

Bridge B

HyperTransport Link

HyperTransport Link

Host

Downstream

Device

PCI-X Bus A

PCI-X Bus B

«
...
48
49
50
51
52
...
»

Содержание TA64





































































































































































Отзывы:

Нет отзывов