manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

HPI Signal Descriptions

 

7-12

7.2.8

Address Strobe Input: HAS

HAS allows HCNTL[1:0], HR/W, and HHWIL to be removed earlier in an ac-
cess cycle, which allows more time to switch bus states from address to data
information. This feature facilitates interface to multiplexed address and data
buses. In this type of system, an address latch enable (ALE) signal is often pro-
vided and is normally the signal connected to HAS.

Hosts with a multiplexed address and data bus connect HAS to their ALE pin
or an equivalent pin. HHWIL, HCNTL[1:0], and HR/W are latched on the falling
edge of HAS. When used, HAS must precede the latest of HCS, HDS1, or
HDS2. Hosts with separate address and data buses can tie HAS high. In this
case, HHWIL, HCNTL[1:0], and HR/W are latched by the latest falling edge of
HDS1, HDS2, or HCS while HAS stays inactive (high).

7.2.9

Interrupt to Host: HINT

HINT is the host interrupt output that is controlled by the HINT bit in the HPIC. This
bit is set to 0 when the chip is being reset. This signal is described in more detail
in section 7.3.4. Thus, the HINT pin is high at reset.

7.2.10 HPI Bus Access

Figure 7–6 and Figure 7–8 show HPI access timing for cases in which HAS is
not used. Figure 7–7 and Figure 7–9 show HPI access timing for cases in which
HAS is used. HSTROBE represents the internally generated strobe described
in Figure 7–5. Control signals: HCNTL[1:0], HR/W, HHWIL, and HBE[1:0] are
typically driven by the host. HCNTL[1:0] and HR/W should have the same val-
ues for both halfword accesses. HHWIL is shown separately to indicate that it
must be low for the first halfword transfer and high for the second. If HAS is not
used (if it is tied high as shown in Figure 7–6), the falling edge of HSTROBE
latches these signals. If HAS is used as shown in Figure 7–7 and Figure 7–9,
the falling edge of HAS latches these values. In this case, the falling edge of
HAS must precede the falling edge of HSTROBE. On a read, data is valid at
some time after the falling edge of HSTROBE. If valid data is not already present
in the HPID, the data is set up at the falling edge of HRDY and held until the rising
edge of HSTROBE. On a write, the host must set up data and HBE[1:0] on the
rising edge of HSTROBE. The HPI provides 32-bit data to the CPU through a
16-bit external interface. This is accomplished by automatically combining two
successive halfword transfers.

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

CAME QBEMFSB2 User Manual preview
QBEMFSB2
Бренд: CAME Страницы: 19
Harmonic XOS User Manual preview
XOS
Бренд: Harmonic Страницы: 56
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Бренд: Direct IP Страницы: 76
Lancom 7100 VPN Manual preview
7100 VPN
Бренд: Lancom Страницы: 70
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Бренд: ICP DAS USA Страницы: 8
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Бренд: SAB Страницы: 29
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Бренд: TVT Digital Страницы: 2
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Бренд: Idis Страницы: 16
ZIMO MXULFA Instruction Manual preview
MXULFA
Бренд: ZIMO Страницы: 13
Omron F3SP-U3P-TGR User Manual preview
F3SP-U3P-TGR
Бренд: Omron Страницы: 29
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Бренд: ICS ELECTRONICS Страницы: 4
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Бренд: B+B SmartWorx Страницы: 120
DigiTech RP 3 User Manual preview
RP 3
Бренд: DigiTech Страницы: 28
SilverStone EXB02 Manual preview
EXB02
Бренд: SilverStone Страницы: 12
ZALMAN CNPS7000B Series User Manual preview
CNPS7000B Series
Бренд: ZALMAN Страницы: 9
Crestron QM-WMC Operation And Installation Manual preview
QM-WMC
Бренд: Crestron Страницы: 52
Cisco SF100D-16P Quick Start Manual preview
SF100D-16P
Бренд: Cisco Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды