manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

Element and Frame/Array Count Updates

 

6-28

6.11 Element and Frame/Array Count Updates

The EDMA parameter RAM has 16-bit unsigned values of element count (EC)
and frame count (FC) each. Additionally, it also holds 16-bit signed values
each for the element index (EIX) and frame index (FIX). The maximum number
of elements in a frame or an array (for 2D transfers) is 65535. The maximum
number of frames in a block is 65536.

The element count and frame count are updated in the corresponding event’s
transfer entry depending on the type of transfer (2D or non-2D) and the syn-
chronization type as shown in Table 6–6.

Table 6–6. EDMA Element and Frame/Array Count Updates

Synchronization

Transfer Mode

Element Count
Update

Frame/Array
Count Update†

Read/write (FS=0)

Non-2D;

(2DS&2DD=0)

–1 
(reload if EC = 1)

See section
6.11.1

–1 
(if element count = 1)

Read/write (FS=0)

2D;

(2DS|2DD=1)

None

–1

Frame (FS=1)

Non-2D;

(2DS&2DD=0)

None

–1

Frame (FS=1)

2D;

(2DS|2DD=1)

None

None

† No frame/array count update occurs if the frame/array count is zero (FC = 0).

6.11.1 Element Count Reload (ECRLD)

There is a special condition for reloading the element count for read/write syn-
chronized (FS = 0), non-2D transfers. In this case the address is updated by
element size or element/frame index depending on SUM/DUM fields. See the
first row in Table 6–7. Therefore, the EDMA controller keeps track of the ele-
ment count to update the address. When a read/write sync event occurs at the
end of a frame (EC = 1), the EDMA controller sends off the transfer request,
and reloads the EC from the element count reload field in the parameter RAM.
This element count reload occurs when element count is one, and the frame
count is non-zero. For all other types of transfers, the 16-bit element count re-
load field is not used because the address generation hardware tracks the ad-
dress directly.

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

3Com 3C16080 Important Information preview
3C16080
Бренд: 3Com Страницы: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Бренд: 3Com Страницы: 74
3Com 3C421600A Installation Manual preview
3C421600A
Бренд: 3Com Страницы: 6
X-Micro XWL-11GPRG Quick Start Manual preview
XWL-11GPRG
Бренд: X-Micro Страницы: 9
X-Micro XWL-11GPAG Quick Installation Manual preview
XWL-11GPAG
Бренд: X-Micro Страницы: 19
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Бренд: Paradyne Страницы: 1
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Бренд: FS Страницы: 19
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Бренд: C&H Страницы: 32
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Бренд: Renesas Страницы: 20
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Бренд: Grundig Страницы: 24
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Бренд: Danville Signal Processing Страницы: 35
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Бренд: Lattice Semiconductor Страницы: 12
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Бренд: GarrettCom Страницы: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Бренд: Adaptec Страницы: 14
IceTech POD-51EH-C541U-12 Operating Instructions Manual preview
POD-51EH-C541U-12
Бренд: IceTech Страницы: 8
Intel IXP28 Series Manual preview
IXP28 Series
Бренд: Intel Страницы: 154
ZyXEL Communications ZyAIR B-100 Quick Installation Manual preview
ZyAIR B-100
Бренд: ZyXEL Communications Страницы: 23
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Бренд: Corsair Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды