manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

SPI Protocol: CLKSTP

 

11-86

11.7.3 McBSP Initialization for SPI Mode

The operation of the serial port during device reset, transmitter reset, and
receiver reset is described in section 11.3.1. For McBSP operation as a master
or a slave in SPI mode, you must follow these steps for proper initialization:

1) Set XRST = RRST = 0 in SPCR.

2) Program the necessary McBSP configuration registers (and not the data

registers) listed in Table 11–2 as required when the serial port is in the
reset state (XRST = RRST = 0) 

except for CLKSTP, which should be dis-

abled. Program CLKSTP to 0Xb if CLKSTP is not disabled.

3) Set GRST = 1 in SPCR to get the sample rate generator out of reset.

4) Wait two bit clocks for the McBSP to reinitialize.

5) Write the desired value into the CLKSTP field in the SPCR. Table 11–21

shows the various CLKSTP modes.

6) Depending on whether the CPU or DMA services the McBSP, either (a) or

(b) should be followed.

a) This step should be performed if the CPU is used to service the

McBSP. Set /XRST = /RRST = 1 to enable the serial port.  Note that
the value written to the SPCR at this time should have only the reset
bits changed to 1 and the remaining bit–fields should have the same
values as in Step 2 and 4 above.

b) If DMA is used to perform data transfers, the DMA should be initialized

first with the appropriate read/write syncs and the start bit set to run.
The DMA waits for the synchronization events to occur. Now, pull the
McBSP out of reset by setting XRST = RRST = 1.

7) Wait two bit clocks for the receiver and transmitter to become active.

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

Omnia 11 Installation And Operation Manual preview
11
Бренд: Omnia Страницы: 102
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Бренд: Measurement Computing Страницы: 27
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Бренд: Avaya Страницы: 5
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Бренд: Cytron Technologies Страницы: 13
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Бренд: Advantech Страницы: 96
iTON ID6ZFN-BK0 User Manual preview
ID6ZFN-BK0
Бренд: iTON Страницы: 12
ekwb SLIM 120 User Manual preview
SLIM 120
Бренд: ekwb Страницы: 36
Watchguard Firebox T85-PoE Hardware Manual preview
Firebox T85-PoE
Бренд: Watchguard Страницы: 27
ADF Web AXIS HD67555 User Manual preview
AXIS HD67555
Бренд: ADF Web Страницы: 20
Domburg Switch Polarization Print HPP4 Quick Start Manual preview
Switch Polarization Print HPP4
Бренд: Domburg Страницы: 11
IEI Technology ECN-360A-D2550 User Manual preview
ECN-360A-D2550
Бренд: IEI Technology Страницы: 141
Lynx LT-FW User Manual preview
LT-FW
Бренд: Lynx Страницы: 42
Johnson Controls NAE55 Series Installation Manual preview
NAE55 Series
Бренд: Johnson Controls Страницы: 36
Intel Water 3.0 Performer C Manual preview
Water 3.0 Performer C
Бренд: Intel Страницы: 2
ARM ARM946E-S Technical Reference Manual preview
ARM946E-S
Бренд: ARM Страницы: 189
Texas Instruments TMS320DM357 User Manual preview
TMS320DM357
Бренд: Texas Instruments Страницы: 167
Roving Networks RN-ISP-UM User Manual preview
RN-ISP-UM
Бренд: Roving Networks Страницы: 21
Tucker-Davis Technologies, Inc. RZ5 Operator'S Manual preview
RZ5
Бренд: Tucker-Davis Technologies, Inc. Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды