manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

Memory Request Priority

9-61

External Memory Interface

9.8

Memory Request Priority

9.8.1

TMS320C6201/C6202/C6701 Memory Request Priority

The ’C6201/C6202/C6701 EMIF has multiple requestors competing for the
interface. Table 9–20 summarizes the priority scheme that the EMIF uses in the
case of multiple pending requests. The priority scheme may change if the DMA
channel that is issuing a request through the DMA controller is of high priority.
This mode is set in the DMA controller by setting the PRI bit in the DMA channel
primary control register.

Once a requester (in this instance, the refresh controller is considered a
requester) is prioritized and chosen, no new requests are recognized until ei-
ther the chosen requester stops making requests or a subsequent higher priority
request occurs. In this case, all issued requests of the previous requester are
allowed to finish while the new requester starts making its requests.

If the arbitration bit of the EMIF global control register is set (RBTR8 = 1) and if
a higher priority requester needs the EMIF, the higher priority requester does not
gain control until the current controller relinquishes control or until eight word re-
quests have finished. If the arbitration bit is not set (RBTR8 = 0), a requester main-
tains control of the EMIF as long as it needs the EMIF or until a higher priority
requester requests the EMIF. When the RBTR8 is not set, the current controller
is interrupted by a higher priority requester regardless of the number of requests
that have occurred.

Table 9–20. TMS320C6201/C6202/C6701 EMIF Prioritization of Requests

Priority

Requestor PRI = 1

Requestor PRI = 0

Highest

External hold

External hold

Mode register set

Mode register set

Urgent refresh

Urgent refresh

DMA controller

DMC

DMC

PMC

PMC

DMA controller

Lowest

Trickle refresh

Trickle refresh

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Бренд: Quantum Страницы: 12
Nvidia nForce 680I LT SLI Hardware User Manual preview
nForce 680I LT SLI
Бренд: Nvidia Страницы: 80
Renesas R0E001000ACB00 User Manual preview
R0E001000ACB00
Бренд: Renesas Страницы: 4
ICP Chapter C Quick Setup Manual preview
Chapter C
Бренд: ICP Страницы: 68
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Бренд: Stahl Страницы: 2
UNICORECOMM UM620N User Manual preview
UM620N
Бренд: UNICORECOMM Страницы: 19
Intel i960 Jx Developer'S Manual preview
i960 Jx
Бренд: Intel Страницы: 578
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Бренд: Corsair Страницы: 30
Intel SRCU31L Quick Start Manual preview
SRCU31L
Бренд: Intel Страницы: 20
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Бренд: S&T Страницы: 115
Intel Braswell Series Technical Manual preview
Braswell Series
Бренд: Intel Страницы: 54
Mod Duo X User Manual preview
Duo X
Бренд: Mod Страницы: 11
nox Hummer H-240CL Manual preview
Hummer H-240CL
Бренд: nox Страницы: 16
IBASE Technology 11th Gen Intel Core U-Series User Manual preview
11th Gen Intel Core U-Series
Бренд: IBASE Technology Страницы: 70
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Бренд: ZyXEL Communications Страницы: 114
C-Data FD612H User Manual preview
FD612H
Бренд: C-Data Страницы: 19
MTL 9468-ET Instruction Manual preview
9468-ET
Бренд: MTL Страницы: 12
Fujitsu PRIMEPOWER 1500 Manual preview
PRIMEPOWER 1500
Бренд: Fujitsu Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды