TERSUS AG960 Скачать руководство пользователя страница 25

Страница: 25 / 168

167

4.1.1.2

Fix the Antenna to the Top of Driving Cab

After installing the satellite navigation antenna at the driving cab top of the tractor is

decided, remove the protective film of 3M double faced adhesive tape on the antenna

pedestal. If the double faced adhesive tape is not adequately adhesive due to low

temperature, heat it with a lighter. Then press the satellite navigation antenna onto the

driving cab top of the vehicle according to the specified position and RF connector

orientation. Press it with force until it is securely adhered. Before pressing, make sure

the contact surface between the driving cab top and the antenna is level with little arc

and is clean without any dust and water drop, or loose connection and falling off of

the antenna may occur. To enhance the water-proof effect of the connection, apply

waterproof sealant around the pedestal of the satellite navigation antenna after

installation.

Figure 21 Remove the protective film of double faced adhesive tape on the antenna pedestal

Figure 22 Heat the double faced adhesive tape in case of low temperature

Содержание AG960









































































































































































Результаты поиска

Содержание AG960

Отзывы:

Бренды по названию

Популярные бренды

TERSUS AG960, Руководство пользователя

Результаты поиска

Содержание AG960

Отзывы:

Бренды по названию

Популярные бренды