TECO F33 Series, Инструкция по эксплуатации, Страница: 126 / 192

Functional Description 123
11.5.2 Digital Inputs [520]
Submenu with all the settings for the digital inputs.
Digital Input 1 [521]
To select the function of the digital input.
On the standard control board there are eight digital
inputs.
If the same function is programmed for more than one
input that function will be activated according to “OR”
logic if nothing else is stated.
Communication information
NOTE: Additional inputs will become available when the
I/O option boards are connected.
Default: RunL
Off 0 The input is not active.
Ext. Trip 3
Be aware that if there is nothing connected
to the input, the VSD will trip at “External
trip” immediately.
NOTE: The External Trip is active low.
NOTE: Activated according to “AND” logic.
Stop 4
Stop command according to the selected
Stop mode in menu [33B].
NOTE: The Stop command is active low.
NOTE: Activated according to “AND” logic.
Enable 5
Enable command. General start condition
to run the VSD. If made low during running
the output of the VSD is cut off immedi-
ately, causing the motor to coast to zero
speed.
NOTE: If none of the digital inputs are pro-
grammed to “Enable”, the internal enable
signal is active.
NOTE: Activated according to “AND” logic.
RunR 6
Run Right command. The output of the
VSD will be a clockwise rotary field.
RunL 7
Run Left command. The output of the VSD
will be a counter-clockwise rotary field.
Reset 9
Reset command. To reset a Trip condition
and to enable the Autoreset function.
Preset Ctrl1 10 To select the Preset Reference.
Preset Ctrl2 11 To select the Preset Reference.
Preset Ctrl3 12 To select the Preset Reference.
MotPot Up 13
Increases the internal reference value
according to the set AccMotPot time [333].
Has the same function as a “real” motor
potentiometer, see Fig. 86.
MotPot
Down
14
Decreases the internal reference value
according to the set DecMotPot time [334].
See MotPot Up.
521 DigIn 1
Stp RunL
A
Pump1
Feedb
15
Feedback input pump1 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Pump2
Feedb
16
Feedback input pump 2 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Pump3
Feedb
17
Feedback input pump3 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Pump4
Feedb
18
Feedback input pump 4 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Pump5
Feedb
19
Feedback input pump5 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Pump6
Feedb
20
Feedback input pump 6 for Pump/Fan con-
trol and informs about the status of the
auxiliary connected pump/fan.
Timer 1 21
Timer 1 Delay [643] will be activated on the
rising edge of this signal.
Timer 2 22
Timer 2 Delay [653] will be activated on the
rising edge of this signal.
Set Ctrl 1 23
Activates other parameter set. See Table
26 for selection possibilities.
Set Ctrl 2 24
Activates other parameter set. See Table
26 for selection possibilities.
Mot PreMag 25
Pre-magnetises the motor. Used for faster
motor start.
Jog 26
To activate the Jog function. Gives a Run
command with the set Jog speed and
Direction, page 97.
Ext Mot
Temp
27
Be aware that if there is nothing connected
to the input, the VSD will trip at “External
Motor Temp” immediately.
NOTE: The External Motor Temp is active
low.
Loc/Rem 28
Activate local mode defined in [2171] and
[2172].
AnIn select 29
Activate/deactivate analogue inputs
defined in [513A], [516A], [519A] and
[51CA]
LC Level 30
Liquid cooling low level signal.
NOTE: The Liquid Cooling Level is active
low.
NOTE: For bipol function, input RunR and RunL needs to
be active and Rotation, [219] must be set to “R+L”.
Modbus Instance no/DeviceNet no: 43241
Profibus slot/index 169/145
Fieldbus format UInt
Modbus format UInt