TANDBERG E5500 Скачать руководство пользователя страница 194

Страница: 194 / 256

Preventive Maintenance and Fault-finding

Page 5-14

Instruction Manual: evolution 5000 E5500 Mobile Contribution Encoder

ST.TM.E10033.3

5.5

Rate Buffer Setting

The MCE, when running in 4:2:2 mode, has two software-selectable rate

buffer modes; small and medium.
When transmitting 4:2:2 mode into systems using the earlier System 3000

PRO IRD M2/PSR/3/422BAS then the rate buffer mode of the MCE must be

set to 'small'.
However, when operating into an Alteia the rate buffer mode of the MCE

must be set to ‘medium’ (default size).
When operating in mixed environments, both the Alteia and the MCE must

be changed to small buffer mode.

NOTE…
These settings can be changed using the VT100 not the front panel menus. Contact Customer

Services for advice (see Preliminary Pages).

Table 5.7: Rate Buffer Settings

MCE Setting

Alteia Setting

PRO IRD

SMALL

Alteia only

MEDIUM

Alteia and PRO IRD

SMALL

NOTE…
Mobile encoders are factory set to use a small rate buffer. If they are not connected to PRO IRDs then

the rate buffer mode may be set to medium.

5.6

Disposing of this Equipment

5.6.1

General

Dispose of this equipment safely at the end of its life. Local codes and/or

environmental restrictions may affect its disposal. Regulations, policies

and/or environmental restrictions differ throughout the world. Contact your

local jurisdiction or local authority for specific advice on disposal.

5.6.2

Lithium Batteries

The equipment uses the Dallas Semiconductor NVRAM DS1644-12

(referred to as NVRAM within this manual). This component contains a

Lithium battery. This battery is not a USA Environmental Protection Agency

listed hazardous waste. It is fully encapsulated, not user serviceable and

should not be tampered with.

Содержание E5500

































































































































































































































































Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды

TANDBERG E5500, Инструкция по эксплуатации

Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды