TANDBERG E5500 Скачать руководство пользователя страница 210

Страница: 210 / 256

Technical Specification

Page B-8

Instruction Manual: evolution 5000 E5500 Mobile Contribution Encoder

ST.TM.E10033.3

B.8.2

EMC

The equipment has been designed and tested to meet the following:

EN 55022

and

AS/NZS 3548

European

Australia

and New

Zealand

Emission Standard

Limits and methods of measurement of

radio frequency interference characteristics

of information technology equipment -

Class A.

EN 61000-3-

European

Electromagnetic Compatibility (EMC), Part 3

Limits; Section 2. Limits for harmonic

current emissions (equipment input current

≤

16 A per phase).

EN 50082-1

European

Generic Immunity Standard

Part 1: Domestic, commercial and light

industry environment.

FCC

USA

Conducted and radiated emission limits for

a Class A digital device, pursuant to the

Code of Federal Regulations (CFR) Title

47-Telecommunications, Part 15: Radio

frequency devices, subpart B -

Unintentional Radiators.

B.8.3

CE Marking

The CE mark is affixed to indicate compliance with the

following directives:
89/336/EEC of 3 May 1989 on the approximation of the

laws of the Member States relating to electromagnetic

compatibility.
73/23/EEC of 19 February 1973 on the harmonisation of

the laws of the Member States relating to electrical

equipment designed for use within certain voltage limits.

NOTE...
The CE mark was first affixed to this product in 2000.

B.8.4

C-Tick Mark

The C-Tick mark is affixed to denote compliance with the

Australian “Radiocommunications (Compliance and Labelling –

Incidental Emissions) Notice made under s.182 of

Radiocommunications Act 1992.

NOTE...
The C-Tick mark was first affixed to this product in 2000.

The EMC tests were performed with the Technical Earth attached, and configured using recommended cables.

The 1

Edition 1992 and the 2

Edition 1997 have been complied with.

Содержание E5500

































































































































































































































































Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды

TANDBERG E5500, Инструкция по эксплуатации

Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды