TANDBERG E5500 Скачать руководство пользователя страница 14

Страница: 14 / 256

Introduction

Page 1-6

Instruction Manual: evolution 5000 E5500 Mobile Contribution Encoder

ST.TM.E10033.3

One channel of asynchronous data and one channel of high speed

synchronous data can also be supported (data channels are not

compressed).
The MCE multiplexes these input signals, under user control, to provide

secure programme transmission. The digital stream is then processed for

forward error correction (FEC) and modulates a single IF carrier for output

to an Up-converter and High Power Amplifier (HPA) equipment for

transmission to the satellite.
If the Compact Remultiplexing option module is fitted, the MCE is capable

of accepting up to three separate transport streams via ASI connectors

and, (together with the host encoder transport stream), provides four

transport streams multiplexed together. Refer to Figure 1.6 and Chapter 4,

Equipment Description for details.
Local control of the equipment is via the front panel keypad and display.

The MCE can also be controlled remotely over an Ethernet interface or

RS-232/RS-485 port. Local health monitoring is incorporated, along with a

local alarm/fail/reset port.
The equipment is fully configurable and extremely flexible, while still being

simple to operate and maintain. Various alignment, testing and diagnostic

facilities have been incorporated to assist with operation and maintenance

in the field.

Figure 1.5: Typical evolution 5000 MCE Configuration

LNB

Up-link equipment
(including
Up-converter and
High Power
Amplifier)

Down-link equipment

(including Low

Noise Block)

VIDEO
AUDIO
ASYNC DATA
SYNC DATA

Encoder

Modulator

VIDEO (ANALOGUE)

VIDEO (DIGITAL)

AUDIO

SYNC DATA

ASYNC DATA

E5500 Mobile Contribution Encoder

ALARM

REMOTE CNTRL

AUTHORIZED

LOCK

BER STATUS

MULTIFUNCTIONAL DISPLAY

ALTEIA

Alteia Satellite Receiver

Содержание E5500

































































































































































































































































Результаты поиска

Содержание E5500

Отзывы:

TANDBERG E5500, Инструкция по эксплуатации, Страница: 14 / 256

Результаты поиска

Содержание E5500

Отзывы: