TANDBERG E5500 Скачать руководство пользователя страница 11

Страница: 11 / 256

Introduction

Instruction Manual: evolution 5000 E5500 Mobile Contribution Encoder

Page 1-3

ST.TM.E10033.3

1.1

Scope of this Manual

1.1.1

Who Should Use this Manual

This manual is written for operators/users of the E5500 Mobile

Contribution Encoder (MCE). The Mobile Contribution Encoder is used as a

stand-alone unit to output a complete modulated transport stream into a

satellite network.
The manual is written to assist in the installation, operation and day-to-day

care of the unit. All information is applicable to all models of the Encoder

unless otherwise stated.

WARNING…

DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT

WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY

TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO

SERVICE THIS EQUIPMENT.

CAUTION…

Unauthorised maintenance or the use of non-approved replacements may affect the equipment

specification and invalidate any warranties.

This manual does not include any maintenance information or procedures

that require the removal of covers.

1.1.2

Software Versions

This manual has been written to cover the functionality of firmware version

1.1 and later of the Motherboard

(S8475) and software version 2.8 and

later of the Host Processor of the Motherboard. The current software

version can be found by viewing the Version Info Menu (see Chapter 3,

Figure 3.9).
This manual continues to be relevant to subsequent firmware issues where

the functionality of the equipment has not changed. Where a new issue of

firmware changes the functionality, a new issue of this manual is provided.

1.1.3

Equipment Covered by this Manual

Equipment Model

Figure 1.1: Mobile Contribution Encoder Front View

The MCE comprises an enclosure with a Motherboard

and Video

Compression Module fitted. The three option slots of the bottom tray are

fitted with a Video Input Module, a Data Input Module and a QPSK

Modulator Card.

S8475 is sometimes referred to as the Base Board 3ASI.

Содержание E5500

































































































































































































































































Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды

TANDBERG E5500, Инструкция по эксплуатации

Результаты поиска

Содержание E5500

Отзывы:

Похожие инструкции для E5500

Бренды по названию

Популярные бренды