TallyGenicom LGe06 Скачать руководство пользователя страница 92

Страница: 92 / 108

A–92

Operator Manual

Offline Data In

Explanation:

Corrective Action:

Offline Dump On

Explanation:

Corrective Action:

Online Download

Explanation:

Corrective Action:

Online Dump On

Explanation:

Corrective Action:

Overflow VFU

Explanation:

Corrective Action:

Paper Motion Flt

Explanation:

Corrective Action:

Paper Out

Explanation:

Corrective Action:

Parity Error

Explanation:

Corrective Action:

Print Fault

Explanation:

Corrective Action:

Replace Rbn

Explanation:

Corrective Action:

The printer is in Offline condition and nonprinted data is in the buffer.

There is no corrective action required. Under normal conditions, the printer

continues to print when it is placed back Online. If you do not want the

buffered data to print, enter the Clear menu by depressing the Clear key

before going back Online and select the Clear Buffers entry to clear the

buffered data.

The printer is in Offline condition and Dump Mode is enabled.

No corrective action is necessary. Place the printer back Online when you

are ready to print.

The printer is receiving downloaded fonts or VFU information.

This message will clear when the download is complete.

The printer is ready to accept and print data from the host through Dump

Mode. All data received from the host will be printed in hexadecimal

format.

No corrective action is required.

An excessive number of bytes has been sent by the host in a VFU down-

load.

Correct data and retransmit from host.

The control processor has detected that the paper has failed to move the

required distance after sending a command to the Paper Drive Motor.

Check for paper feed problems. If there are any paper feed problems,

correct them, then press the Clear key to clear the fault. If there are no

paper feed problems and the condition does not clear, call your Customer

Service Representative.

Paper is not being detected by the Paper Out sensor.

If this message is correct, refer to the Paper Loading sections in Chapter 2,

then load paper. If the fault does not clear, call your Customer Service

Representative for repair.

Parity is enabled and a mismatch on Bit 8, between the computer and the

printer, has been detected on the currently active host interface.

If there is a mismatch between the setting of the printer and the setting of

the host, you can change printer parity. See the Config Menu section in

Chapter 3.

If there is no mismatch between the printer and host settings, then the

data sent from the host has been corrupted. Retransmit the data from the

host. If the condition repeats, set up the printer for Dump Mode (see the

Config Menu section in Chapter 3), and retransmit the data again. If you

find no errors in the Dump Mode data, call your Customer Service

Representative for repair.

Faulty communication between the main and control processor has

occurred causing a dot row to misprint. The printer automatically recovers

from this condition.

Under normal circumstances there is no corrective action other than to

depress the Clear key to remove the fault message from the display. If,

however, this problem persists, call your Customer Service Representative

for repair.

Caused when Rbn Monitor has reached its set level.

Check/Replace the ribbon then reset the Rbn Monitor.

Error Messages

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды