TallyGenicom LGe06 Скачать руководство пользователя страница 14

Страница: 14 / 108

1–14

Operator Manual

DO NOT power up your printer before removing the shipping

hardware.

CAREFUL!

Unpacking your printer

Instructions for unpacking your printer are located on the outside of the shipping

container. After you have removed your printer from its container, store the

shipping materials for possible later use.

Repacking

Repacking your printer for storage or shipping is the reverse order of unpacking.

If shipping materials are needed, you can reorder them from your dealer.

Removing the Shipping Hardware

The Shipping Hardware consists of 4 screws, identified by red tags, that secure the

printer base to the inside mechanism, and tie restraints that secure the Paper

Stacking Chains. The shipping screws fasten from underneath, 2 near the front of

the print cabinet and 2 near the rear of the cabinet.

Figure 1 - 1. Shipping Screw Locations

Unpacking the Printer

Arrows point to 4

shipping screw locations

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды