TallyGenicom LGe06 Скачать руководство пользователя страница 22

Страница: 22 / 108

1–22

Operator Manual

Control Panel Components

The Control Panel is located on the right front top of the printer housing. It is

used to program and direct most printer functions.

Figure 1 - 10. Control Panel

32-character

2-line LCD

display

Green LED Indicator

Red LED Indicator

beeper

}

LED Indicators

The green ONLINE indicator illuminates whenever there is power to the printer,

and the printer is Online.

The red FAULT

Indicator illuminates whenever an error or fault is detected. A

message also appears on the display to indicate what kind of fault is present (see

Appendix A for explanations of all error and fault messages).

LCD (Liquid Crystal Display)

The 32-character, 2-line Liquid Crystal Display shows printer status, menu selec-

tions, normal, fault and error messages. It is divided into four main areas. The

displayed information will vary with menu selection and the configuration of the

printer.

Control Panel Components

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды