TallyGenicom LGe06 Скачать руководство пользователя страница 41

Страница: 41 / 108

Chapter 3:

Printer Menus and the Control Panel

3–41

Clear Key continued

Clear Cancel (Twinax and Coax only)

Allows you to send a Cancel Job message to the host via the I/O while the printer

is Offline. It performs the same functions as the Cancel Job request when the

printer is Online. The display reads "Cancel Job" and the printer remains

Offline.

For Coax, this function is valid only in NonSCS mode.

Clear Reprint (Coax only)

This allows you to reprint the previous buffer contents. After reprinting the

buffer, the printer returns to Enable Print condition and continues printing the

rest of the job. This option is convenient in cases of paper jams or any time you

do not need to send the complete job.

This function is valid only in Non SCS Mode. If you select this in SCS Mode, an Invalid Key error

message displays for a few seconds.

Config Key

Offline

This is a “shortcut” to the Load Configurations menu item (see later in chapter),

allowing you to enter a menu where any of ten saved configurations can be

loaded into the Current Configuration.

Use the Up and Down Arrow keys to scroll through the configurations. Pressing

the Enter key loads the one you choose.

Control Panel Key Functions

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды