TallyGenicom LGe06 Скачать руководство пользователя страница 100

Страница: 100 / 108

C–100

Operator Manual

Physical Configurations

Your printer is available in table top and enclosed pedistal configurations.

Weight

Table Top 6306 with paper exit guide assembly:

115.4 lbs.

Table Top 6312 with paper exit guide assembly:

124.1 lbs.

Pedestal Mounted 6306 with paper exit guide and paper tray: 159.9 lbs.

Pedestal Mounted 6312 with paper exit guide and paper tray: 168.6 lbs.

Dimensions

Table Top 6306 and 6312

Width:

28.3 inches

Height:

13.0 inches

Depth:

14.4 inches

Depth with paper exit guide assembly: 23.4 inches

Pedestal Mounted 6306 and 6312

Width:

28.3 inches

Height:

39.7 inches

Depth:

23.4 inches

Depth with paper exit guide assembly: 29.4 inches

Depth with paper tray:

29.5 inches

Preventive Maintenance

This printer is designed to eliminate the requirement of scheduled maintenance

procedures, such as alignment, adjustment, or lubrication. Preventive mainte-

nance is limited to periodic cleaning.

Dust and paper fibers should be removed

periodically with a soft cloth and brush or a vacuum cleaner. Clean the printer

case with a damp cloth and soapy water.

DO NOT

use any abrasive cleaners or

solvents, as they will damage the case.

Environment

Operating

Temperature (Dry Bulb):

50°F to 104°F (10°C to 40°C)

Humidity:

10 to 90% noncondensing with a maximum wet bulb

temperature of 82°F (28°C) and a minimum dew point of

36°F (2°C )

Altitude:

To 8,000 ft. (2438 meters)

Industry and Agency Standards

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды