TallyGenicom LGe06 Скачать руководство пользователя страница 59

Страница: 59 / 108

Chapter 3:

Printer Menus and the Control Panel

3–59

Config Menu

⇒

Printer

Config Menu

Following are explanations of each category and

parameter in the Config Menu. For all available

options under each parameter below, consult the

Help Menu printout. The categories here are

Printer, Codes, Graphics, Configurations, Serial

I/O, Parallel I/O, IntelliFilter, and when the

options are installed, Twinax/Coax and IPDS.

Printer Category

Use the Arrow and Enter keys to select

Menu => Config Menu => Printer to get

here.

Powerup

This parameter sets the printer either

Online

Offline

when the power switch is

turned on. The default is Offline.

Ser/Par Emulation

This parameter allows you to define which set of printer control commands will

be emulated for data received on the Serial and Parallel ports (except LAN-

IPDS).

DEC LG

is the default selection.

When a new emulation setting is entered through the Printer Control Panel,

emulation dependent parameters in the Current configuration are changed to

match the default settings for the selected emulation. The following table lists

those parameters by emulation:

Parameter

DEC LG+

Tally ANSI

Genicom ANSI P5000

P6000

Character Set

Latin1

Code Pg 437

Code Pg 850

Latin1

OCR-A

ANSI

OCR-B

ANSI

Auto CR

OFF

Line Wrap

OFF

Wrap LF

OFF

Code 7F

Delete Buffer FILL

FILL

Space

VT Channel

N/A

Skip When

N/A

Before

N/A

After

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды