TallyGenicom LGe06 Скачать руководство пользователя страница 98

Страница: 98 / 108

B–98

Operator Manual

If you are installing a printer on an active system, go through the following list

before connecting the Twinax cable(s).

•

Verify that the printer address matches the one given it on the host and

that no addresses are duplicated anywhere on the line. You can check the

address of the printer by accessing the HELP Menu on your printer

control panel and printing out a Control Panel Selections Printout (see

Chapter 3).

•

Make sure the printer is turned OFF.

•

Terminate the device immediately up cable (between the printer and the

host) from the printer.

•

Any jobs going to devices down cable (between the printer and the end of

the network) must be put on HOLD.

•

Place any devices that are down cable from the printer OFFLINE.

Now connect the cable from the out connector of the up cable device to either

side of the Host Connector Smart T and if there are devices down cable, connect

the cable going to them to the other side of the Smart T. The Smart T

automatically takes care of terminating the Twinax line or allowing throughput of

data to devices located down cable from the printer.

Coax Interface

This interface is optional and requires the installation of an additional interface module.

Make

sure that the printer is turned off. To connect to a Coax system, use the BNC

adapter (a DB-15 to Coax). Connect the adapter to the Host Interface plug on

the printer I/O. The Coax interface allows a maximum of 5,000 feet (1.5 km)

from the host computers to the printer.

Figure B - 2. Twinax Smart “T” Adaptor

Your Twinax hookup is now complete and it is time to test your printer to verify

its operation. Load your printer with paper and an ink ribbon. Run the IBM

printer verification test. If the test is successful, your installation is complete.

Figure B - 3. BNC Coax adapter

Optional Interfaces

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды