TallyGenicom LGe06 Скачать руководство пользователя страница 75

Страница: 75 / 108

Chapter 3:

Printer Menus and the Control Panel

3–75

DTR Function

continued...

Offline:

When this option is active, the DTR Line is used to signal only that the

printer is Online or Offline. Unlike the Busy option, the Offline option will not

interfere with operation of the Xon/Xoff Communication Protocol.

Power:

When this option is active, the DTR Line is used to signal the host that

the printer is powered up. This DTR Selection will not interfere with host recep-

tion of the Xoff/Xon Serial Protocol, because unlike the Busy selection, the DTR

Signal is not toggled at the same time as the Xoff Signal. When using this option,

the DTR Polarity parameter must be set to Actv Hi.

If your system is configured to use Xon/Xoff Protocol, using the Busy option above will cause interfer-

ence with printer to host communication. You may however, use the DTR Line to signal the host that

the printer is Offline or that the printer is powered up (Offline and Power options, respectively).

DTR Polarity

This parameter is used to set the DTR Signal polarity. Active Low is the default.

Busy Polarity

This parameter allows you to control the polarity of the Busy Signal. Active Low

is the default.

RTS Function

The RTS line of the serial interface has been used to indicate Busy in addition to

the DTR line. This option allows the RTS line to either be continuously High or

to function as Busy (default).

Robust Xon

This parameter behaves the same as a normal Xon/Xoff protocol, except that

with this parameter enabled, the Xon code will be sent every 5 seconds when the

printer is ready to accept data. OFF is the default.

Config Menu

⇒

Serial I/O

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды